All Makes All Models OER Products - Steering

Reproduction of the original power steering pressure hose for use with various 1970-76 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each hose is manufactured to specific factory dimensions replicating the original in...

Reproduction drag link for 1965-66 Chevrolet Impala and full size models. Includes hardware; zerk fittings, washers, cotter pins, and castle nuts. End joints are greaseable. Ready to install.

Reproduction of the original pitman arm for 1962-70 Dodge and Plymouth B-Body models. Each reproduction pitman arm is manufactured to factory specifications featuring heat treated components and forging. Comes complete with...

Reproduction of the original steering column coupler components commonly known as the rag joint. These special components can be a weak link between the steering column and the steering gear box. Each set includes the correct...

OER reproduction of the original steering coupling joint for various models. This coupler (rag joint) is required to connect the steering column to the steering box. Coupler Specs: Shaft Size: 3/4" coarse spline with flat at...

Reproduction of the original power steering return hose for use with various 1971-79 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each hose is manufactured to specific factory dimensions replicating the original in...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has unfinished hardware that are designed to be used with a...

This OER® power steering pump rebuild set includes the parts you will need to rebuild your old power steering pump. Refer to your factory service manual for instructions. Applications AMC: 1968-88 All Models - With...

Restorer's Choice™ premium replacement idler arm for 1965-73 Mopar C-body models. These vital suspension components are commonly worn and in need of replacement. They are often responsible for steering misalignment,...

Reproduction of the original power steering Ram hoses designed for use on 1962-67 Chevy II and Nova models. Each hose is manufactured to factory specifications using OE materials duplicating the original in fit and function....

Reproduction power steering pulley washer and nut. This lock-nut and washer set is needed to secure the power steering pulley to the pump. Measures 9/16" - 18. Pre-packaged in OER polytube. 1967-75 Camaro 1967-75 Firebird...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is black phosphate...

Reproduction of the original power steering pressure hose for use with various 1970-76 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each hose is manufactured to specific factory dimensions replicating the original in...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the original control arm bushing designed for use on various Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM...

Replacement power steering pressure hose for 1965-68 Impala, Bel Air, and Biscayne models with small block engine. A leak in your power steering system can make a mess of your engine compartment, your driveway and garage...

Is your steering loose or front end out of alignment? Parts in your steering system may be worn out or damaged. Now you can rebuild your classic's steering linkage system with this OER® reproduction. Sold individually....

Reproduction of the original inner tie-rod end designed for use with various 1965-70 GM models including 1965-68 Impala, Full Size, and 1965-70 Chevy and GMC truck models. Is your steering loose or front end out of alignment?...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the 12-point, grade 8 bolt that secures the steering coupler to the steering shaft on most GM vehicles. The original couplers came with a 12-point bolt in the location where tightening this bolt squeezes the...

Reproduction of the original big block power steering adjustor bracket designed for use with 1965-68 Chevrolet Impala and Full Size, 1967-68 Camaro, and 1968 Nova models with big block engines. Manufactured in stamped steel,...

Reproduction power steering hose set for 1955-57 V8 models with original style power steering. This complete 4 piece set includes the high pressure hose, low pressure hose and 2 control valve hoses with correct fittings and...

OER® Authorized reproduction steering coupler found on various models. Each coupler replicates the original in every detail. A worn out steering coupling joint will cause your vehicle?s steering to become loose or...

Reproduction of the original style power steering return hose used on various GM and Dodge, Plymouth models as listed below. A leak in your power steering system can lead to a very serious and possibly dangerous situation....

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is the chrome plated set...

Reproduction bolt used to mount the steering box to the frame. Will work on both power or manual steering boxes. This is a 7/16" bolt that is 4-5/8" long. Use as required.

Authentic reproduction of the original power steering pressure control valve return fitting for the steering sector on 1965-66 various Dodge and Plymouth models. The return hose of the power steering pump attaches to this...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This is the O-ring set for Saginaw power steering pumps. Includes 8 pieces to re-seal the pump to the reservoir. Does not include the shaft seal. Fits most Saginaw pumps through 1977 including Saginaw P series. Chevrolet...

Quality reproduction of the original pitman arm designed for various GM models. Manufactured to exact factory specifications. Each assembly features heat treated components and forging, and precision machining tolerances....

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

OER® Original Hue Saginaw Blue-Gray paint is specifically formulated to perfectly match the factory colors of specific components installed on your vehicle at the factory. Unique shades are available so that you can...

Authentic reproduction of the original power steering pressure control valve return fitting for the steering sector on 1967-74 various Dodge and Plymouth models. The return hose of the power steering pump attaches to this...

Reproduction of the original power steering return hose for use with various 1970-76 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each hose is manufactured to specific factory dimensions replicating the original in...

Reproduction of the originual style power steering hose for use with various 1963-80 GM, Chrysler, Dodge, and Plymouth models as listed. A leak in your power steering system can lead to a very serious and possibly dangerous...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This is a quality OER® reproduction of the deep groove power steering pump pulley. This pulley is stamped with the original GM part #3941105. Single groove, 5-3/4" o.d. Applications: Camaro 1969 302ci 1969 396ci, 427ci...

Reproduction of the original power steering pressure hose for use with various 1971-79 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each hose is manufactured to specific factory dimensions replicating the original in...

Reproduction of the original pitman arm for 1970-72 Dodge and Plymouth E-Body and 1971-72 Dodge and Plymouth B-Body models. Each reproduction pitman arm is manufactured to factory specifications featuring heat treated...

OER reproduction of the original steering coupling joint designed for use on various GM and Ford models. This coupler (rag joint) is required to connect the steering column to the steering box. Each steering coupler is...

Steering rebuild kit for 1965-71 F-100 and F-250 2-wheel drive trucks. This kit includes all the necessary components to completely renew the front steering system on a 2wd Ford pickup. Applications: 1965-72 F-100 - all...

This spacer is used between the power steering pump and mounting bracket on 1967-69 Pontiac Firebird models with a V8 engine. 2 required.

Convenient set of hardware for steering shaft couplers on many GM vehicles. Set includes the (1) 3/8"-24 hex nut and lock washer and (1) 5/16"-24 nut and lock washer. Also includes the 12-point coupler bolt that secures the...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has chrome hardware that are designed to be used with a chrome...

OER® reproduction of the original small block power steering adjustor bracket for use with various 1965-68 GM small block models. Manufactured in stamped steel, this bracket was original installed for a variety of...

Quality reproduction of the original pitman arm designed for 1963-67 Chevy II/Nova and X-body models with manual steering. Manufactured to exact factory specifications. Each assembly features heat treated components and...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the original big block power steering brackets designed for use on 1969 Camaro, Impala, Nova, and Chevelle models. This set includes all three brackets needed to replace or add a new power steering pump...

Reproduction of the original power steering brackets that attach the two power steering hoses to the inside of the left side frame rail. This steel bracket holds the hoses that run from the power steering pump to the power...

Idler arm assembly for various 1969-74 Pontiac models as listed. This pivoting support for the steering linkage appears on older recirculating ball-type steering systems (pre-rack & pinion) and functions like the pitman arm...

Reproduction of the original center drag link designed for use with various GM models as listed. Each drag link is manufactured in quality forged steel that replicates the original size and configuration offering a superior...

Correct reproduction of the original power steering bracket designed for use with various 1969-1972 Chevrolet models wirh small block engines. Each bracket is manufactured in stamped steel replicating the original...

This OER® line clamp is manufactured from die stamped steel. Each piece is plated in clear zinc to help protect it from rust and corrosion. Clip slips over the high pressure line and is secured to the gear box top cover...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This is the hose adapter fitting for Saginaw power steering gear box or pump. Straight, inverted flare zinc coated steel, 5/8"-18 to -6AN. Fits most Saginaw gear boxes or pumps 1960 through 1977 including Saginaw P series. ...

Reproduction of the original power steering pump cap for various GM models from 1961-72. This is not a factory service replacement or aftermarket cap, this is a reproduction of the OEM style cap with an exact metal design...

This is a quality OER® reproduction of the original power steering pump pulley designed for use on various GM applications..This pulley is manufactured to exact factory specifications and stamped with the original GM part...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Quality reproduction of the original pitman arm designed for 1967-68 Firebird models with V8 engine and power steering. Manufactured to exact factory specifications. Each assembly features heat treated components and...