All Makes All Models OER Products - Power Steering System

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is the chrome plated set...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction power steering hose set for 1955-57 V8 models with original style power steering. This complete 4 piece set includes the high pressure hose, low pressure hose and 2 control valve hoses with correct fittings and...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the original power steering brackets that attach the two power steering hoses to the inside of the left side frame rail. This steel bracket holds the hoses that run from the power steering pump to the power...

OER® reproduction of the original small block power steering adjustor bracket for use with various 1965-68 GM small block models. Manufactured in stamped steel, this bracket was original installed for a variety of...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has chrome hardware that are designed to be used with a chrome...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This spacer is used between the power steering pump and mounting bracket on 1967-69 Pontiac Firebird models with a V8 engine. 2 required.

Reproduction power steering pulley washer and nut. This lock-nut and washer set is needed to secure the power steering pulley to the pump. Measures 9/16" - 18. Pre-packaged in OER polytube. 1967-75 Camaro 1967-75 Firebird...

Reproduction of the original big block power steering brackets designed for use on 1969 Camaro, Impala, Nova, and Chevelle models. This set includes all three brackets needed to replace or add a new power steering pump...

Authentic reproduction of the original power steering pressure control valve return fitting for the steering sector on 1965-66 various Dodge and Plymouth models. The return hose of the power steering pump attaches to this...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This is the O-ring set for Saginaw power steering pumps. Includes 8 pieces to re-seal the pump to the reservoir. Does not include the shaft seal. Fits most Saginaw pumps through 1977 including Saginaw P series. Chevrolet...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Authentic reproduction of the original power steering pressure control valve return fitting for the steering sector on 1967-74 various Dodge and Plymouth models. The return hose of the power steering pump attaches to this...

Reproduction bolt used to mount the steering box to the frame. Will work on both power or manual steering boxes. This is a 7/16" bolt that is 4-5/8" long. Use as required.

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the original power steering Ram hoses designed for use on 1962-67 Chevy II and Nova models. Each hose is manufactured to factory specifications using OE materials duplicating the original in fit and function....

This is a quality OER® reproduction of the deep groove power steering pump pulley. This pulley is stamped with the original GM part #3941105. Single groove, 5-3/4" o.d. Applications: Camaro 1969 302ci 1969 396ci, 427ci...

Reproduction of the original power steering pump cap for various GM models from 1961-72. This is not a factory service replacement or aftermarket cap, this is a reproduction of the OEM style cap with an exact metal design...

This is a quality OER® reproduction of the original power steering pump pulley designed for use on various GM applications..This pulley is manufactured to exact factory specifications and stamped with the original GM part...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

This OER® line clamp is manufactured from die stamped steel. Each piece is plated in clear zinc to help protect it from rust and corrosion. Clip slips over the high pressure line and is secured to the gear box top cover...

OER® reproduction power steering pump pulley for various GM models from 1960-75. Manufactured from formed and machined steel with the correct key way fit design and finished in satin black paint. This is a single groove...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Correct reproduction of the original power steering bracket designed for use with various 1969-1972 Chevrolet models wirh small block engines. Each bracket is manufactured in stamped steel replicating the original...

This OER® power steering pump rebuild set includes the parts you will need to rebuild your old power steering pump. Refer to your factory service manual for instructions. Applications AMC: 1968-88 All Models - With...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has unfinished hardware that are designed to be used with a...

This is the hose adapter fitting for Saginaw power steering gear box or pump. Straight, inverted flare zinc coated steel, 5/8"-18 to -6AN. Fits most Saginaw gear boxes or pumps 1960 through 1977 including Saginaw P series. ...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Reproduction of the original big block power steering adjustor bracket designed for use with 1965-68 Chevrolet Impala and Full Size, 1967-68 Camaro, and 1968 Nova models with big block engines. Manufactured in stamped steel,...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is black phosphate...