All Makes All Models OER Products - Weatherstrip

Reproduction of the original door frame weatherstrip that installs on the outer frame of the door on 1967 Camaro and Firebird models. Manufactured in the correct configuration which allows easy installation when replacing the...

OER® reproduction of the original rubber tailgate bumpers for 1967-72 GM Fleetside pickup truck models. Replacing the tailgate rubber stoppers will help prevent problems associated with a misaligned tailgate. Each rubber...

Reproduction of the original seat back rubber stoppers designed for use on various 1961-79 GM models. These rubber stoppers help prevent rattling and keep the seat back positioned correctly. Replace worn out or missing seat...

Reproduction of the anti-rattle rubber bumper for the glove box door on 1982-85 Impala and 1982-93 Caprice models and for the ash tray on 1990 Caprice models. Measures 5mm in height and fits a 3mm hole. 2 required per...

Reproduction door rubber bumpers for 1949-1958 full size Chevrolet cars including Impala and Bel Air models. Designed to help keep your door aligned and in the correct position. Each bumper duplicates the original and fits...

Reproduction of the original T-Top weatherstripping designed for use with 1982-92 Camaro and Firebird, and Trans Am models. Installs exactly as original and will help eliminate rattles and noise caused by insufficient...

Reproduction tail lamp lens gaskets for 1962-64 Chevy II/Nova models. This is the gasket that installs between the tail lamp housing and the lenses. Includes RH and LH tail lamp gaskets manufactured in die-cut foam. 1 pair...

Reproduction of the original style door frame weatherstrips designed for use with 1955-57 Chevrolet Bel Air, Pontiac Chieftain, Starchief, and 1957 Bonneville two door hardtop and convertible models. Creates a weather-tight...

Reproduction of the original tailgate stop rubber bumper for use with 1955-57 Chevrolet Nomad models. Manufactured in EPDM rubbe replicating the original configuration for an authentic appearance and fit. Some wagons and...

Factory-style replacement rubber bumper set for all 1971 Dodge & Plymouth B-body models. Set includes (see note below): Door bumpers Hood side bumpers Hood adjust bumpers Ashtray bumpers Glove box bumpers Trunk bumpers Fuel...

Reproduction of the original inner splash apron set designed for use on 1969 Camaros. The splash shields are important in maintaining the seal between the fender skirt and engine bay. Replace the old and worn out splash...

OER® reproduction of the original GM speedometer cable grommet for all 1961-64 full size Chevrolet models. Designed to factory specifications in the correct configuration for a perfect fit and manufactured in rubber as...

Reproduction of the original trunk weatherstrip designed for use on various 1971-76 Mopar A, B and E-Body models. Each trunk weatherstrip is designed in a D profile configuration matching the original in fit and appearance....

Reproduction of the original weatherstrip seal that fits onto the bottom of the door and acts as an auxiliary weatherstrip protecting water or elements from entering the passenger area. The door frame weatherstrip works in...

OER® reproduction of the original rubber stoppers for use with all 1969 standard Camaro models. The kit includes all of the correct rubber stoppers needed for the doors, hood, trunk lid, console, glove box and rear...

Quality reproduction of the original outer door mirror gasket designed for use on various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors....

Quality reproduction of the original speedometer cable firewall grommet designed for use on various 1962-70 GM models. This grommet is manufactured to replicate the original in every detail. Installs where the speedometer...

Correct reproduction of the of the original U-shaped rubber door jamb rubber seals designed for use on 1965-66 GM Full Size models. Each U-shape seal is manufactured to original specifications including a steel insert...

Correct reproduction of the original roof rail weatherstrips designed for use on 1971-74 Mopar B body 2 door hardtop models. The roof rail seal runs along the top roof line of the car and seals the door glass at the roof....

Achieve a clean appearance by replacing the rubber stoppers. The stoppers can wear out and cause problems with the body panels. The stoppers will help keep your panels in the correct alignment positions.M The kit includes...

Reproduction of the original cowl firewall seals to replace the old or worn out originals on 1967-68 Camaro and Firebird models. Each seal is die-cut to exact dimensions and replaces the various gaskets on the outer firewall...

Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Measures 1 5/8" O.D. and fits a 1-1/4" hole.

Reproduction of the rubber bumper to fit a variety of GM models and applications. Sold individually. Refer to detailed applications below. Buick Applications- For Door Pull Handles: Regal 1991-92 - rear door Skylark 1986-91...

Reproduction of the original vertical quarter glass weatherstrip seals designed for 1971-74 Mopar E-Body hardtop (coupe), or convertible models. Manufactured to factory specifications with proper contours to correctly replace...

Quality reproduction of the original hood to cowl weatherstrip seal that attaches to the cowl panel and seals the area between the hood and windshield. This correctly configured seal is manufactured to exact specifications...

Reproduction of the original outer door remote mirror mounting gasket for use with the various applications listed. Each gasket is manufactured to replicate the original is fitment and design. Can be used with the original...

Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...

Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...

Reproduction of the original front hood weatherstrip seal designed for use on 1991-96 Chevrolet Caprice and 1994-96 Impala models. Each hood seal is manufactured from durable rubber in the original configuration for a perfect...

Correct OER® reproduction of the original weatherstrip designed for use on 1960-66 Chevrolet and GMC pickup, panel and Suburban models. Each weatherstrip is manufactured in quality EPDM rubber material replicating the...

Reproduction of the original weatherstripping designed for use on 1982-92 Camaro and Firebird models. This weatherstrip attaches to the plastic corner filler at the front of the side windows on all 1982-92 models. Each...

OER® reproduction of the original hood to cowl rubber seal weatherstrip will keep the rain and other elements out of your engine compartment. Each seal is manufactured to exact specificationa and replaced the original...

Exact reproduction of the original door frame weatherstrip that installs on the outer frame of the rear door on 4 door Chevy II and Nova models. Manufactured in the correct configuration which allows easy installation when...

Reproduction of the original convertible weatherstripping designed to replace the original cracked, deteriorated or worn out original weatherstrip. Each set includes 5 seperate weatherstrips needed to replace the front...

Reproduction of the original common rubber bumpers and stoppers used in 1962-65 Chevy II and Nova models. Each stopper kit includes a variety of rubber bumpers and stoppers that will replace the commonly missing or worn out...

Keep your interior protected from the elements and reduce cabin noise by replacing your dried-out, cracked or just plain missing original weatherstrip with this reproduction weatherstrip kit. Each weatherstrip component...

Reproduction of the original convertible top frame runner stoppers designed for use with 1967-69 Camaro and Firebird convertible models. Stoppers are used to keep the top frame separated when folding into the well. ...

This 2-piece reproduction, authentic style, window felt weatherstrip kit is made in the USA with very high quality materials, just like original. Does both front doors, and fits 1962-65 Ford Falcon or Mercury Comet (4-door...

This special front fender and front spoiler welting is designed to help to seal fender flares or front spoiler extensions to the body. Although the configuration can vary from model to model, this welting can be used...

Keep your interior protected from the elements and reduce cabin noise by replacing your dried-out, cracked or missing original weatherstrip with this reproduction weatherstrip kit. Each weatherstrip component is...

Correct reproduction of the original power window harness rubber boots which is used to house the power window wiring harness as it passes between the door jamb and door area. This rubber boot is manufactured in durable...

Reproduction of the original AC hose grommet designed for use on 1967-68 GM models. Located on the RH front fender well, this hose grommet insulates the AC hoses from the condensor to the engine compartment. Manufactured in...

Reproduction of the original door jamb rubber U shaped rubber seals designed for use on 1968-70 Dodge and Plymouth B-Body 2 door hardtop models. Each seal mounts on the rear top edge of the quarter panel door jamb area at...

Replace the old splash aprons with this quality reproduction and keep your engine compartment clean and free of water, salt, and other road debris. Each splash apron set is designed to fit as original ensuring a complete seal...

Correct reproduction of the quarter window U-shape rubber weatherstrip originally installed on 1967-68 Impala Custom and Caprice hardtop and convertible models. This seal attaches to the door jamb area under the quarter...

Reproduction of the original GM windshield seal lock strip designed for use on 1985-92 Camaro and Firebird models. This rubber lock strip helps to hold the windshield glass in place and fill the gap between the glass and the...

OER® reproduction of the original front fender gasket set for use with 1947-55 Chevrolet and GMC truck models. Each gasket set is designed to replace the front fender gaskets for both RH and LH sides. Always use new...

Reproduction of the original trunk weatherstrip designed for use on 1968-69 Plymouth B-body models. Each rubber strip is manufactured with correctly configured extruded rubber. The weatherstrip is designed to fit the groove...

This 2-piece window felt weatherstrip kit is just like original. Does both doors, and fits 1962-65 Ford Falcon or Mercury Comet 2-Door Sedan (w/T-Bird Roof) rear quarter window Glass Run Channels. Sometimes called an...

Excellent reproduction of the original rear body to bumper weatherstripping designed for use on 1965-65 Chevy II and Nova models. The bumper to body seal strip is designed to seal and fill the area where the rear bumper meets...

OER reproduction of the original shaker hood scoop to hood seal designed for use on 1977-81 Trans Am models. This reproduction is manufactured to exact specifications ensuring a tight seal once installed. Features correct OE...

Keep your interior protected from the elements and reduce cabin noise by replacing your dried-out, cracked or missing original weatherstrip with this authentic style reproduction weatherstrip kit. Each weatherstrip ...

Reproduction of the original rear side marker gaskets designed for use on all 1968 Firebird models. Each gasket is die-stamped in OE type gasket material featuring same thickness as original. Manufactured in black. Sold in...

Reproduction of the original upper fuel neck rubber sleeve designed for use on 1967-68 Chevrolet Camaro models. This reproduction rubber sleeve surrounds the gas tank neck and protects against gasoline, water or other...

Factory-style reproduction rubber bumper set for 1972-74 Plymouth A-body models. Set includes (see note below): Door bumpers Hood side bumpers Hood adjust bumpers Ashtray bumpers Glove b ox bumpers Trunk bumpers Fuel door...

Reproduction of the original style door frame weatherstripping designed for use on 1968-70 Dodge and Plymouth 2-door hardtop models. Each weatherstrip is manufactured and designed to factory specifications and manufactured...

Reproduction of the original hood to cowl seal weatherstrip for use on 1970-74 Mopar E-body models. This weatherstrip will help keep water and dirt out of the engine bay by sealing the area between the cowl panel and hood. ...

This 4-piece reproduction, authentic style, window felt weatherstrip kit is made in the USA with very high quality materials, just like original. Does both front doors, and fits 1966-67 Ford Ranchero Glass Run Channels....

Factory-style replacement door seal end caps designed for use on 1970-74 Dodge and Plymouth E-Body hardtop and convertible models. This end cap is mounted to the door edge with screws and caps off the edge of the door...

Keep your interior protected from the elements and reduce cabin noise by replacing your dried-out, cracked or missing original weatherstrip with this authentic style reproduction weatherstrip kit. Each weatherstrip component...