All Makes All Models OER - Clutches & Parts

Perfectly constructed pair of brake and clutch pedal assemblies designed for use on 1967-68 Camaro, 1967 Firebird and 1968 Chevy II, Nova models. Each pedal assembly is manufactured to OE specifications that mount and...

Reproduction of the original components needed to replace the cluch linkage on 1967 Camaro small block and 1967 Firebird (L6) models. You?ll be pleased with this all new pre-packaged clutch linkage set. Whether replacing worn...

Correct reproduction of the original brake and clutch pedal pad trim plate designed for use on various 1967-81 GM models with manual transmission. Each pedal trim plate is designed to replicate the original in fit, appearance...

This small bushing is essential to keep the clutch push rod in the proper location. This OER® injection molded plastic bushing installs on the clutch pedal and retains the clutch push rod. This is a commonly worn out...

Correct reproduction of the original brake and clutch pedal pad designed for use on a variety of GM models equipped with manual transmissions and drum brakes. Manufactured in quality EPDM rubber replicating the original...

Reproduction of the commonly worn out nylon clutch pedal bushings designed for use on many various GM and Ford vehicles as listed. Split nylon flange bushings fit over clutch pedal cross shaft and inside cross shaft sleeve...

Reproduction of the original clutch and brake pedal assembly designed for use with 1962-65 Chevrolet Nova models. These perfectly constructed brake and clutch pedal assemblies are manufactured in quality stamped steel...

Replacement clutch linkage bell crank ball stud nylon bearing for 1962-76 Mopar A, B and E-Body vehicles. Designed using factory specifications to replace the original exactly. Sold in pairs. 2 pair required per vehicle. ...

OER® reproduction of the original brake and clutch pedal pad designed for use on 1955-59 Chevy/GMC truck models. Brake design is same as original including correct ribbed design. For use on 2nd design 1955 models with...

OER® reproduction of the original upper clutch push rod designed for use on various GM models. Each rod is manufactured in stamped steel and replicates the original in quality and design. Will fit and install as original....

Reproduction of the original pedal pads designed for use on 1976-81 Camaro, Firebird and various other GM models. This pedal pad set is designed to replace the worn out original pads for models with disc brakes and manual...

Reproduction of the original brake pedal pad for 1962-66 Dodge and Plymouth models with an automatic transmission. Measures 6" x 2". Mopar Authentic Restoration & Trade; Product. Applicati ons 1963-66 A-body 1962-65 B-body

Reproduction of the original clutch and brake pedal assembly designed for use with 1966-67 Chevrolet Nova models. These perfectly constructed brake and clutch pedal assemblies are manufactured in quality stamped steel...

Reproduction of the original pedal pads designed for 1969 Firebird models. This pedal pad set is designed to replace the worn out original pads for 1969 Firebird models with manual transmission. Replacing the pedal pads will...

OER® reproduction clutch fork return spring. Attaches from the engine mounting bracket to the clutch extension wire. Measures 3-5/8" O.L. 2-1/2" spring portion. Applacations: 1967-69 Camaro small block 1967-69 Firebird...

Reproduction of the original components needed to replace the cluch linkage on 1968-69 Camaro big block models, 1968-74 Chevy II / Nova big block models and 1968-69 Firebird (V8) models. You?ll be pleased with this all new...

Precision reproduction of the original clutch bellcrank assembly designed for use on Camaro and Nova big block applications. Each assembly includes a zerk grease fitting for easy maintenance. This fitting will allow...

OER® reproduction of the original frame side clutch bellcrank pivot ball bracket designed for use on 1970-81 Camaro and Firebird models with manual transmissions. This steel bracket attaches to the vehicles frame....

Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3" brake...

OER® precision reproduction of the original 9" bellcrank assembly designed for use on various GM models. Each bellcrank is manufactured to factory specifications and features a zerk grease fitting for easy maintenance....

OER® reproduction of the original clutch fork return spring which attaches from the clutch fork to the frame rail on models with manual transmissions. This reproduction spring replicates the original in every detail. Will...

OER® reproduction of the original frame side bellcrank pivot bacll beacket designed for use on various GM models. Each bracket is die-blanked and formed with the correct offset and holes for mounting. 1 bracket required...

OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...

This complete kit is designed to replace pedal pads and trim plates on 1970-71 models with floor mounted gas pedal , drum brakes and a manual transmission. For models with the 3" clutch pedal. To ensure proper fit, measure...

Reproduction of the original brake and clutch pad designed for use on various GM models with a manual transmission and standard brakes. Each pad is manufactured in quality RPDM rubber replicating the original in quality and...

Reproduction of the original brake and clutch pedal pad designed for use on various 1958-70 Chevrolet models with manual transmissions. Each pedal pad is manufactured in EPDM rubber to factory specifications and replicates...

Reproduction of the original frame side clutch bellcrank pivot ball bracket for use with 1962-67 Chevy II Nova models with a manual transmission. This die-formed stamped steel bracket features the correct contours and SAE...

OER® reproduction of the original lower clutch push rod adjustor designed for use on various GM models. This push rod is manufactured to original specifications and includes the swivel. Will replace any original non...

Precision reproduction of the original clutch bellcrank unit designed for use on 1962-67 6- cylinder and small block Chevy II and Nova models. This bellcrank is manufactured in stamped steel and replicates the original in...

OER® reproduction of the original upper clutch push rod boot designed for use with various 1970-81 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each clutch rod boot is manufactured in quality EPDM rubber matching the...

OER® reproduction of the original clutch fork bellhousing boot specifically designed for various GM models from 1955 to 1983. This reproduction boot will replace the old or worn out original exactly. Manufactured in...

OER® reproduction of the original brake or clutch pedal pad for 1947-55 Chevy and GMC truck models. Manufactured to exact specifications and includes correct configuration for originality. Fits 1955 (1st design) models....

This complete kit is designed to replace pedal pads and trim plates on 1970-71 models with floor mounted gas pedal , drum brakes and a manual transmission. For models with the 3" clutch pedal. To ensure proper fit, measure...

OER® reproduction of the lower clutch push rod designed for use on various GM models. Includes right angle shell portion correctly swaged and internally threaded to match the lower clutch push rod adjuster for 6 cylinder...

Reproduction of the original components needed to replace the clutch linkage on 1967 Camaro big block models, and 1967 Firebird V8 models. You?ll be pleased with this all new pre-packaged clutch linkage set. Whether replacing...

Correct reproduction of the original return spring extension rod designed for use on various GM models as listed. This rod is used in conjuntion with the clutch fork return spring. Together they connect the clutch fork to the...

Reproduction of the original brake or clutch pedal pad for 1962-65 Dodge and Plymouth models with a manual transmission. Mopar Authentic Restoration™ Product Sold individually.

Reproduction of the original Mopar A-body clutch pedal push rod designed for use on all 4-speed equipped 1968-74 Mopar A-Body vehicles. Each push rod is manufactured to OE specifications to ensure a quality replacement....

Reproduction of the original style clutch housing and flywheel cover plate designed for use on a variety of 1964-81 Chevrolet models as listed. Manufactured in stamped steel to original specifications that replicate the...

Reproduction of the original clutch linkage bell crank nylon wear washer designed for use with various 1962-76 Dodge and Plymouth A, B and E-Body models. Manufactured to original specifications in quality injection molded...

Reproduction of the original clutch bell crank linkage spring clip designed for use on almost all 1962-76 Mopar A, B and E-Body vehicles. The clip is manufactured to replicate the original in every detail using factory...

OER® reproduction of the original clutch pedal return spring designed for use on all 1973-81 Camaro and Firebird models. Each spring is manufacturer to correct factory dimensions and replaces the old or worn out original....

OER® reproduction brake and clutch pedal pad for 1960-72 Chevrolet and GMC trucks. Manufactured as original using premium grade rubber, this pad features the correct waffle style patten. Chevrolet Applications 1960-72 C/K...

Correct reproduction of the original brake or clutch pedal pad trim plate for use on various 1965-72 Pontiac models. Each trim plate is manufactured to exact factory dimensions and features the bright polished finish that was...

Reproduction of the original brake and clutch pedal pads for 1966-70 Dodge and Plymouth models including Barracuda, Belvedere, Charger, Coronet, Cuda, Dart, GTX, Road Runner, Satellite, Superbird and Valiant models with a ...

Reproduction of the original components needed to replace the clutch linkage on 1968-69 Camaro small block models, 1968-74 Chevy II / Nova models and 1968-69 Firebird (L6) models. You?ll be pleased with this all new...

Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and 2-3/8" clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3"...

OER® reproduction of the original clip that was used for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower...

This is The plastic clutch Z bar insert set that allow the bar to pivot on the clutch ball These are present on most all GM cars from 1962-81 with a manual transmission. This four piece set which includes 3 nylon bushings and...

Reproduction of the original clutch pedal push rod designed for use with manual transmission-equipped 1968-70 Mopar B-Body vehicles. Each push rod is manufactured to factory specifications ensuring a correct replacement of...

Reproduction of the original clutch linkage components designed to replace the clutch linkage on 1972-81 Camaro small block or big block models. Each comprehensive clutch linkage set includes the necessary components to...

Reproduction of the original brake or clutch pedal pad designed for use with 1970-72 Dodge and Plymouth models including Barracuda, Challenger, Charger, Coronet and Road Runner models with a manual transmission. Each pad is...

Reproduction of the original clutch flywheel housing cover designed for use on various 1975-81 GM vehicles with Borg Warner T-10 manul transmissions. This cover is used to protect the clutch flywheel housing for vehicles with...

Reproduction of the original pedal pads designed for 1967-68 Camaro and Firebird models. This pedal pad set is designed to replace the worn out original pads for models with disc brakes and manual transmissions. Replacing the...