All Makes All Models OER Products - Transmission

Reproduction speedometer cable - 58" with grommet (thread on style).

OER® reproduction shifter installation hardware set for models equipped with a floor console and horseshoe automatic shifter. Includes correct factory style clips to attach the shift cable to the base and all necessary...

OER® reproduction of the ventilator used by GM on a multitude of applications from the 1950s thru todays cars and trucks including the rear axle housing, automatic transmissions. front transfer case on 4 x 4 models and...

Reproduction of the original clutch bell crank linkage spring clip designed for use on almost all 1962-76 Mopar A, B and E-Body vehicles. The clip is manufactured to replicate the original in every detail using factory...

Reproduction of the original speedometer cable retainer clip designed for use with various for 1969-85 General Motors vehicles. This retainer clip is manufactured in stamped steel replicating the original design. Retains the...

OER® reproduction of the original clip for use with automatic transmissions shift levers. Attaches the shift knob to the lever on vehicles equipped with factory GM auto trans console shifter. A necessary clip required to...

Reproduction of the original components needed to replace the clutch linkage on 1968-69 Camaro small block models, 1968-74 Chevy II / Nova models and 1968-69 Firebird (L6) models. You?ll be pleased with this all new...

Reproduction of the original style clutch housing and flywheel cover plate designed for use on a variety of GM models. Manufactured in stamped steel to original specifications that replicate the original cover. The clutch...

OER® reproduction of the original upper clutch push rod designed for use on various GM models. Each rod is manufactured in stamped steel and replicates the original in quality and design. Will fit and install as original....

Correct reproduction of the original return spring extension rod designed for use on various GM models as listed. This rod is used in conjuntion with the clutch fork return spring. Together they connect the clutch fork to the...

OER® reproduction of the original lower clutch push rod adjustor designed for use on various GM models. This push rod is manufactured to original specifications and includes the swivel. Will replace any original non...

Replace damaged or missing shifter boot bezels to seal the area around the shift mechanism just like the factory intended. This shifter boot bezel or trim ring seals the boot to area where the shift mechanism protrudes...

Reproduction of the original components needed to replace the clutch linkage on 1967 Camaro big block models, and 1967 Firebird V8 models. You?ll be pleased with this all new pre-packaged clutch linkage set. Whether replacing...

OER® reproduction of the original frame side clutch bellcrank pivot ball bracket designed for use on 1970-81 Camaro and Firebird models with manual transmissions. This steel bracket attaches to the vehicles frame....

Reproduction of the original brake or clutch pedal pad designed for use with 1970-72 Dodge and Plymouth models including Barracuda, Challenger, Charger, Coronet and Road Runner models with a manual transmission. Each pad is...

Reproduction of the original Mopar A-body clutch pedal push rod designed for use on all 4-speed equipped 1968-74 Mopar A-Body vehicles. Each push rod is manufactured to OE specifications to ensure a quality replacement....

OER® reproduction of the original flywheel pan (also called a torque converter cover) for use with various 1962-73 Chevrolet models. Each flywheel pan cover, aka the torque drive convertor cover is manufactured to OE...

This is a reproduction of the lower speedometer cable as was used on 1967-69 Camaro models and 1982 Camaro models equipped with a 4-speed manual with cruise control. This reproduction is manufactured exactly like the...

The lower kickdown rod which was used on 1967-1972 Camaro models with factory installed V8 engines and Powerglide transmissions, is a commonly forgotten link in your vehicles drive train. This rod mounts between the...

Correct OER® reproduction throttle valve cable for various 1976-80 GM models with TH350 automatic transmissions. This cable is manufactured to original specifications. Applications: 1976-77 Buick Skylark 305, 350-L TH350...

OER® reproduction of the original frame side bellcrank pivot bacll beacket designed for use on various GM models. Each bracket is die-blanked and formed with the correct offset and holes for mounting. 1 bracket required...

OER® reproduction of the lower clutch push rod designed for use on various GM models. Includes right angle shell portion correctly swaged and internally threaded to match the lower clutch push rod adjuster for 6 cylinder...

OER® reproduction clutch fork return spring. Attaches from the engine mounting bracket to the clutch extension wire. Measures 3-5/8" O.L. 2-1/2" spring portion. Applacations: 1967-69 Camaro small block 1967-69 Firebird...

This is a reproduction of the lower speedometer cable. This reproduction is manufactured exactly like the original, and is a thread-on design. The cable measures 24" in length. Applications: Camaro 1967-69 3 Speed with...

OER® precision reproduction of the original 9" bellcrank assembly designed for use on various GM models. Each bellcrank is manufactured to factory specifications and features a zerk grease fitting for easy maintenance....

OER® reproduction of the original clip that was used for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower...

Quality reproduction of the original console shift lens for use on 1964 Impala SS models with powerglide transmissions. Each lens is manufactured to factory specifications including the letters P-R-N-D-L. Will replace the...

Reproduction of the original shifter slider plate designed for 1971-74 E-Body and 1971-74 B-Body Mopar vehicles equipped with an automatic transmission and center console. Each slider plate is manufactured to correct...

Reproduction of the original shifter boot and bezel designed for use on 1966-74 Mopar A, B, and E- body models. Each shift boot is designed and manufactured in EPDM molded rubber compound replicating the original in fitment...

Reproduction of the original shift button emblem designed for use on 1976-81 Pontiac Firebird models. Each emblem is manufactured in quality injection molded ABS to factory specifications. Includes correct gold and black bird...

Reproduction of the original transmission crossmember designed for use on models originally equipped with a Turbo 400 transmission and a big block engine. This reproduction is manufactured in quality stamped steel ensuring an...

OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...

Reproduction of the original brake and clutch pad designed for use on various GM models with a manual transmission and standard brakes. Each pad is manufactured in quality RPDM rubber replicating the original in quality and...

Reproduction of the original components needed to replace the cluch linkage on 1968-69 Camaro big block models, 1968-74 Chevy II / Nova big block models and 1968-69 Firebird (V8) models. You?ll be pleased with this all new...

Reproduction of the original clutch linkage bell crank nylon wear washer designed for use with various 1962-76 Dodge and Plymouth A, B and E-Body models. Manufactured to original specifications in quality injection molded...

OER® reproduction transmission cable bracket for TH400 transmission. Applications: Buick: 1977 Regal with console Chevrolet Cars: 1973-74 Camaro with console 1974-75 Chevelle Oldsmobile: 1976-77 Cutlass with console ...

Reproduction of the original speedometer assembly designed for use with 1964 Chevrolet Impala, Bel Air, and Biscayne models. Each speedometer is manufactured to correct factory specifications. Features correct markings, turn...

OER® reproduction of the original clutch fork return spring which attaches from the clutch fork to the frame rail on models with manual transmissions. This reproduction spring replicates the original in every detail. Will...

Reproduction of the original Hurst-type shift boot retainer plate installed on various GM models including 1969 Chevrolet Camaro models with 4 speed Hurst shifters. Works with original or reproduction Hurst shift boots. This...

OER reproduction of the original floor shift boot manufactured in quality molded rubber replicating the original GM boot in authenticity and fitment. Originally installed on all 1967-68 Camaro models with 4 speed trans, 1969...

Authentic reproduction of the original style shift knob used with Muncie 4 speed transmissions of the 1960s. This white shift knob is manufactured in quality ABS with a steel insert. This 1-3/4" shift knob can be installed on...

Reproduction of the original clutch pedal push rod designed for use with manual transmission-equipped 1968-70 Mopar B-Body vehicles. Each push rod is manufactured to factory specifications ensuring a correct replacement of...

OER® reproduction of the original GM speedometer cable grommet for all 1961-64 full size Chevrolet models. Designed to factory specifications in the correct configuration for a perfect fit and manufactured in rubber as...

Reproduction of the original stamped steel shift lens backing plate designed for use on 1968-69 Camaro consoles with auto trans. This backing plate fits under the automatic transmission shift indicator lens on all 1968-69...

Correct reproduction of the original brake or clutch pedal pad trim plate for use on various 1965-72 Pontiac models. Each trim plate is manufactured to exact factory dimensions and features the bright polished finish that was...

OER® reproduction of the original correct plastic torque converter cover (also called a flexplate/flywheel cover) for use with TH350 transmissions and a 153 tooth flex plate. Applications: 1967-69 Camaro V8 1970-73...

Correct reproduction of the original brake and clutch pedal pad trim plate designed for use on various 1967-81 GM models with manual transmission. Each pedal trim plate is designed to replicate the original in fit, appearance...

Reproduction of the original shift boot retainer plate designed for use on 1970-81 Camaro and Firebird models with 3/speed or 4/speed manual transmissions. Each gearshift boot retainer plate is manufactured in stamped steel...

This is an exact OER® reproduction of the original pivot ball screw, which provides the pivot for the bellcrank and screws into the bellhousing. Used on a big and small block models. Applications: 1963-66 GM trucks...

Precision reproduction of the original clutch bellcrank assembly designed for use on Camaro and Nova big block applications. Each assembly includes a zerk grease fitting for easy maintenance. This fitting will allow...

OER® reproduction supplemental shifter hardware set which includes all necessary brackets, bushings, bolts, spacers, washers and screws to rebuild a horseshoe shifter assembly. For Chevrolet models equipped with a floor...

Replace the deteriorated or missing original upper shift boot of your Hurst Pistol-Grip shifter-equipped Mopar B or E-Body to seal the area around the shift mechanism the way the factory intended. For models with center...

Quality reproduction of the original speedometer cable designed for use with various 1962-83 Buick, Chevrolet, Oldsmobile, and Pontiac models. This complete speedometer cable assembly is manufactured to correct factory...

Reproduction of the original upper shift boot designed for use on 1970-81 F-Body models with manual transmission. Each boot is manufactured in quality molded rubber to replicate factory specifications and provide an original...

OER® reproduction of the correct shift cable for with automatic transmissions. Manufactured to original specifications including components required to completely replace your original cable. Measures 30" Applications:...

OER reproduction of the original leather wrapped shift knob for use on 1987-02 Camaro and 1988-96 Regal / GS models with automatic transmission. Manufactured in injection-molded material and hand-wrapped in genuine leather as...

Reproduction of the original brake and clutch pedal pad designed for use on various 1958-70 Chevrolet models with manual transmissions. Each pedal pad is manufactured in EPDM rubber to factory specifications and replicates...

Reproduction of the original firewall speedometer cable clip designed for use on various GM models. Originally used on cars with factory installed 4-speed transmissions, this unique retainer clip is used to hold the...

Quality reproduction of the original speedometer cable firewall grommet designed for use on various 1962-70 GM models. This grommet is manufactured to replicate the original in every detail. Installs where the speedometer...

Reproduction of the original black plastic tunnel located directly below the shift plate and extends downward to the rubber shift boot. This reproduction is manufactured in a precision injection molded black injection molded...