1966-71 Dodge, Plymouth; Hood Insulation Clip; Black Metal 1-3/4" x 1/2"; Each
Rproduction of the original hood insulation clip designed for use on various 1966-71 Mopar models. Clip is designed and manufactured in stamped steel to replicate the original. Will fit and function properly. This clip was...
Hood Prop Rod For Fiberglass Hood
Hood prop required when installing a fiberglass hood on you Camaro. Since hood springs are not recommended when using fiberglass hoods, this prop is essential for keeping your hood open while working in the engine...
1958-77 GM; Hood Adjuster Bolt and Nut Set ; 5/16"-18 x 1-3/8"; Various Models
Reproduction of the original hood stop bolt and nut set designed for use on various 1958-77 GM models. This bolt and nut set will keep the hood adjusted to the proper height. These 5/16"-18 x 1-3/8" bolts include the correct...
1969-1970 Pontiac GTO, LeMans; Ram Air; Hood Pan; Template
This is a template for marking and the under brace structure to install the upper ram air pan to the hood of a 1969-70 Pontiac GTO. Take the guess work out and do it right with this template. All hoods from the factory where...
Reproduction hood pin rubber gasket found on models with hood pins. Each gasket is die-cut to proper dimension. Will also fit a wide variety of aftermarket hood pins. Sold individually. Use as required. Check measurements...
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set ; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1967-72 Chevy C10, Blazer, Jimmy, Suburban; Hood Bumper Set ; 6 Piece Set
GMCApplications: 1967-1972 GMC Pickup Truck 1967-1972 GMC Suburban 1970-1972 GMC Jimmy
1980-2016 GM; Hood Adjust Rubber Bumper; Outer Side; Each
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1965-1970 GM; Hood Insulation Fastener Set; 20 Piece Set; Various Models
Reproduction of the original hood insulation fasteners designed for various 1965-69 GM models. Manufactured in injection molded ABS plastic to replace OE part number # 3909199. These are an exact copy of the OE retainer for...
1967-72 Chevy, GMC Pickup, Blazer, Suburban; Hood Side Rubber Stopper Set ; 4 Piece
OER® reproduction of the original hood to fender rubber stoppers designed for use on 1967-72 Chevrolet and GMC truck models. These uniquely designed bumpers will replace the originals exactly offering years of service...
1947-55 GM Truck Hood Rubber Bumper Set ; 10 Piece Set
OER® reproduction of the original truck hood rubber bumpers designed for use on 1947-55 Chevrolet and GMC truck models. Each rubber bumper is manufactured to replicate the original. Replace the old or worn out bumpers with...
1965-81 Hood Latch Pilot Bolt; 4"
OER® reproduction of the 4" hood latch pilot bolt for use on various GM models as listed below. The bolt is designed to attach to the lock plate retainer. Once installed, the hood pop up spring surrounds this bolt....
1982-92 Firebird Hood Side Bumper, Each
Correct reproduction of the original rubber bumper designed to replace the hood panel side bumpers on all 1982-92 Firebird models. Designed to prevent rattling and helps to keep the hood aligned properly. Sold individually. 4...
1974-81 Camaro; Hood Lock Latch Bracket; RH Passenger Side
Reproduction of the hood lock latch support for 1974-81 Camaro models. This stamped steel piece supports the hood latch from the passenger side on all 1974-81 models. Features a black electrophoretically deposited coating...
1978-81 Camaro; Hood Latch Bracket; LH; Driver Side
Reproduction hood lock latch support for 1978-81 Camaros. This stamped steel bracket supports the hood latch from the driver side on all 1978-81 models. Includes threaded nut inserts for installation. Features a black...
1963-66 Dodge/Plymouth A-Body; Hood Side Rubber Bumper; Each
OER reproduction of the original hood side rubber bumper designed for various 1963-66 Mopar A-Body models. Each rubber stopper is designed to factory specifications to correctly replace the hood side stop bumper. Sold...
1970-74; Challenger Hood Front Rubber Bumper; Each
Correct reproduction of the original front hood rubber bumper designed for use on 1970-74 Challenger models. Each bumper is designed to replace the original exactly. Manufactured from quality EPDM rubber material for long...
1973-91 GM Truck Hood Side Bumper, Each, Pickup, Blazer, Jimmy, Suburban
OER® reproduction of the original hood side bumper designed to keep the hood aligned on 1973-91 Chevrolet and GMC models including Blazer, Jimmy and Suburban. This bumper is manufactured from extruded rubber and fit on...
1955-57 Chevrolet / GMC Truck Hood Rubber Bumper Set ; 10 Piece Set
OER® reproduction of the original truck hood rubber bumpers designed for use on 1955-1957 Chevrolet and GMC truck models. Each rubber bumper is manufactured to replicate the original. Replace the old or worn out bumpers...