All Makes All Models OER Products - AC & Heater

Reproduction of the original style spring clips designed to attach the air conditioning vent assembly to the steeing clumn cover vent, and the glove box door mounted vent. Includes 4 clips. 2 short clips for steering column...

OER® reproduction of the original dash heater control knobs designed for use on various 1965-1989 GM models. Each knob is reproduced to exact dimensions and cosmetically correct. Manufactured in injection molded ABS and...

Reproduction of the original heater hose tie strap for all 1960-76 A. B and E models. This strap has various purposes, most commonly it was used to hold the heater hoses together. Use as required. Manufactured from correct...

Quality OER reproduction of the original heater control knobs for fan, heat, temperature and defroster controls. Beautifully chrome plated with a bright finish. Set includes four chrome die-cast knobs with the correct...

Unique reproduction of the original rubber grommet for use on air conditioned vehicles to seal and support the heater core outlet tubes to the evaporator core case. Officially Licensed GM Restoration Part® Camaro...

Replacement heater core mounting strap for 1982-92 Camaro models. Each strap is designed to secure and retain heater core?s inside the under dash heater assembly box. Manufactured from high quality stamped steel and is plated...

Correct reproduction of the original lower outer dash air outlet deflector for 1982-1992 Camaro models with air conditioning. This authentic reproduction deflector mounts vertically to the outside of the dash. Sold...

Reproduction of the original heater switch plate designed for use on 1964-66 Mustangs. Each plate is a manufactured to duplicate the original in quality and appearance. This is the chrome die-cast metal plate that the heater...

Reproduction of the original heater fan switch designed for use on various 1969-79 GM models without air conditioning. Each switch is a replication of the original heater fan switch and installs into the heater control...

Reproduction of the original steel clamp designed to mount the heater core on a wide variety of 1977-92 GM models including 1982-92 Camaro and Firebird. A perfect replacement for the unsightly, worn out or missing original...

Reproduction of the duct connector that connects the vent elbow to the firewall duct on 1968 models without factory AC. The original ducts often become cracked or worn over time. This reproduction duct is manufactured to...

OER reproduction of the original dash pad defroster vents designed for use on all 1982-92 Camaro dash pads. These plastic injection molded vents insert on the outer sides of dash pad and direct air flow to the side windows....

Reproduction of the original casted heater control levers designed for use on various GM models. Includes 3 precisely stamped levers, 3 original style chrome knobs and mounting hardware. Manufactured to original...

Reproduction of the original dash vent bezel retainer designed for use on various GM models. This much needed retainer is used to retain the dash vent bezel to the dash assembly. Manufactured to replicate the original using...

Reproduction of the original dash vent bezel retainer adapter designed for use on various GM models. The dash vent bezel adapter is manufactured in quality injection molded ABS plastic replicating the original in fitment and...

OER® reproduction of the original dash heater control knobs designed for use on various 1965-1989 GM models. Each knob is reproduced to exact dimensions and cosmetically correct. Manufactured in injection molded black ABS...

OER® reproduction of the original chrome lower dash air deflector assembly for 1963-81 Pontiac models with air conditioning. Located below glove box and steering column and considered an adjustable lap vent. This reproduction...

Reproduction of the original vacuum actuated air conditioning clutch switch designed for use on various GM models including 1967 Camaro and Firebird models with air conditioning (C.A.C). Each clutch switch will replace the...

Reproduction of the original heater switch plate designed for use on 1964-66 Mustangs. Each plate is a manufactured to duplicate the original in quality and appearance. This is the chrome die-cast metal plate that the heater...

Reproduction of the original heater and AC blower switch designed for use on all original heater control assemblies for the applications listed below. Manufactured to original specifications, each switch will fit and function...

OER® reproduction of the original heater control cable assemblies designed for use with 1969 Camaro and 1969-74 Nova and X-body models. Include all 3 necessary cables for control panel operation on vehicles with air...

Reproduction of the original AC hose grommet designed for use on 1967-68 GM models. Located on the RH front fender well, this hose grommet insulates the AC hoses from the condensor to the engine compartment. Manufactured in...

Reproduction of the original dash side vent bezel designed for use on various GM models with factory air conditioning. This dash air vent holds the air outlet vent assembly on the RH passenger side of the dash. Manufactured...

Keeping your air flow ducts operational is what this cable is all about. Reproduction air flow control cable with original style black knob. 51 .5" long, cut as required for some applications. Camaro applications: 1969-70...

OER® reproduction of original evaporator case drain hose that attaches to the bottom portion of the evaporator core outlet case on various 1966-70 GM models originally equipped with air conditioning. Each drain hose is...

OER® reproduction of the original center dash outlet deflector used with various 1977-1990 Chevrolet center air vent assemblies. Manufactured of high quality injection molded ABS and accented with silver color painted...

OER® reproduction of the original heater control cable assemblies designed for use with 1969 Camaro and 1969-74 Nova and X-body models. Includes all 3 necessary cables for control panel operation on vehicles without air...

Reproduction of the original dash side vent assembly designed for use on 1970-81 Camaro models. Each dash vent is injection molded to OED specifications and includes correct louvers allowing for a complete replacement. Will...

OER Reproduction heater blower motor resistor for various GM non air conditioned models. Each resistor is an exact reproduction of the original GM component designed to fit and function same as the original AC Delco resistor....

These reproduction rubber spacers are used in the center dash vent of various GM vehicles including 1967-68 Camaro and Firebird models. They slide into the slots on both sides on the back of the dash vent bezel where the...

Commonly broken inner half of air conditioning case core box. This is a fiberglass reproduction of the inner portion of the air conditioning condenser cover. This item is usually found broken or cracked due to replacement...

Reproduction of the original heater hose to cylinder head fitting designed for various 1972-81 Pontiac models. Fitting presses into the rear of the passenger side cylinder head and features a tapered edge for more convenient...

OER reproduction of the original blower motor resistor designed for use on 1973-81 Camaro models with air conditioning. Each resistor is an exact reproduction of the original GM component, designed to fit and function just...

Reproduction of the retaining clip used to attach the air deflector vent to the lower steering column cover on the drivers side (below the steering column) on 1970-81 Firebird models with air conditioning. Sold as a pair. 1...

Reproduction of the retaining clip designed to attach the air deflector vent to the glove box door on the passenger side on 1970-81 Firebird models with air conditioning. Sold as a pair. 1 pair required per vent.

Reproduction dash pad defroster vents designed for all 1982-92 Firebird dash pads. Each vent is injection molded using quality ABS materials. Vents install on the outer sides of dash pad and direct air flow to the side...

OER® quality reproduction of the original Astro Ventilation parts. Kit includes: Left hand (driver side) black vent bezel Right hand (passenger side) black vent bezel 2 chrome vent balls 2 Dash b ezel vent retainers 1...

Reproduction of the original dash vent ball designed for use on various Pontiac Firebird models. This reproduction vent ball air deflector replicates the original in quality and design. Manufactured in injection molded ABS,...

Reproduction of the original elbow style shut-off assembly designed for use with 1967-69 Camaro and Firebird models. Each valve is manufactured in injection molded ABS that replicates the original is quality and design. These...

Reproduction of the original elbow style shut-off assembly designed for use with 1967-69 Camaro and Firebird models. Each valve is manufactured in injection molded ABS that replicates the original is quality and design. These...

Reproduction of the insulator for axial type AC compressors for various GM models with air conditioning. This rubberized insulator mounts the AC condensor to the radiator core support with two threaded ends and include nuts. ...

This quality reproduction fan switch fits various 1967-69 GM models without A/C. Replaces original switch exactly. Officially Licensed GM Restoration Part® Applications: 1967-68 Chevrolet Bel Air 1967-68 Chevrolet...

Correct reproduction of the original center dash air outlet deflector originally installed on 1982-1992 Camaro models with air conditioning. Each air deflector is manufactured to exact specifications and injection molded for...

Reproduction of the original Camaro side dash vent assembly designed for use on 1970-81 Camaro models with air conditioning. This injection molded reproduction is designed and manufactured to exact factory specifications....

Reproduction of the original heater control fan switch designed for use on various GM models including 1969 Camaro models. Each switch will fit and install same as original in the heater control assembly. Mounts to the rear...

Reproduction of the original heater control blower switch designed for use on various GM models including 1969 Camaro models. Each switch will fit and install same as original in the heater control assembly. Mounts to the...

Reproduction of the original center dash air vent assembly for use with 1967-68 Camaro and Firebird models with air conditioning. Manufactured in die-cast zinc to factory specifications featuring a bright polished chrome...

Commonly broken inner half of air conditioning case core box. This is a fiberglass reproduction of the inner portion of the air conditioning condenser cover. This item is usually found broken or cracked due to replacement...

Reproduction of the original dash side vent assembly designed for use on 1970-81 Camaro models. Each dash vent is injection molded to OED specifications and includes correct louvers allowing for a complete replacement. Will...

Reproduction of the original dash side vent designed for use on 1969 Camaro models without air conditioining. Each dash side vent features a chrome plated air vent with correctly textured black plastic fins. Vent housings are...

Reproduction of the original style gaskets needed to replace the air duct seals on the various models listed. Each set contains all die-cut solid and sponge rubber for resealing leaky Astro ventilation systems. Contains cowl...

After many years of use, the defroster vent unit will become brittle and possibly crack, especially in cold weather. Replacing the vent assembly will once again allow the air flow to be directed upward to the window making...

Reproduction of the original defroster duct designed for use on various 1969-79 GM models. Each defroster vent assembly is manufactured to OE specifications and replaces the old or damaged original exactly. Unit installs...

Reproduction of the original dash air vent bezel designed for use with 1967-68 Camaro and Firebird models with air conditioning. The AC vent bezel surrounds the adjustable dash vent ball. Manufactured to correct factory...

Reproduction of the original style gaskets needed to replace the air duct seals on the various models listed. Each set contains all die-cut solid and sponge rubber for resealing leaky Astro ventilation systems. Contains cowl...

Reproduction of the original bracket used to mount the air conditioning condenser to the radiator support. For use on all 1967-1969 small block or big blocks with A/C. Includes left hand (driver side) and right hand...

Reproduction of the original air vent bezel unit designed for use on various GM applications. Each bezel is manufactured in injection molded ABS and chrome plated to a bright lusterious shine replicating the original in...

Reproduction of the original air vent bezel unit designed for use on various GM applications. Each bezel is manufactured in injection molded ABS and includes correct black design replicating the original non deluxe style...

Reproduction of the original air vent bezel unit designed for use on various GM applications. Each bezel is manufactured in injection molded ABS and includes correct black design replicating the original non deluxe style...

Reproduction of the original air vent bezel unit designed for use on various GM applications. Each bezel is manufactured in injection molded ABS and chrome plated to a bright lusterious shine replicating the original in...