1959-66 Pontiac; Tri-Power Throttle Body; For 389/421 Engine
Reproduction Tri-Power throttle body assembly for 1959-66 Pontiac models with a 389 or 421 engine. This throttle body is manufactured out of Die Cast and features the carburetor shaft as well as the butterflies. The front and...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1967-75 Various GM Applications; Quadra Jet Carburetor Base Gasket; Heat Shield
Reduces heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket fits 67-75 GTO/Firebird, 67-75 Camaro, Chevelle, El...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
1968-71 Firebird, Trans Am; Quadrajet Throttle Shaft and Choke Set; 3 Piece Set
Reproduction of the original quadrajet throttle shaft and choke set designed for use with various 1968-71 Pontiac models including Firebird and Trans Am models. This show quality set contains the key components to repair or...
Holley Carburetor Float Bowl Screws; Set of 8
Reproduction set of 2-1/2" flat blade carburetor fuel bowl screws for Holley carburetors. These special screws are specifically designed in the correct original configuration with the proper head design for the early model...
1955-79 Air Cleaner to Carb Gasket; 5-1/8" .060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1967-77 Pontiac Firebird, 1967-73 GTO; Dust Boot; Accelerator Pump; Quadrajet Ram Air
Reproduction of the accelerator pump dust boot for 1967-77 Firebird and 1967-73 GTO with a Quadrajet Ram Air setup. The accelerator mounts inside the carburator and is operated by a lever. This boot keeps dust and other...
1967-68 Firebird; Lower Foam Pan Seal; with Ram Air
Correct reproduction of the original lower foam Ram Air pan seal designed for use with 1967-68 Pontiac Firebird models with Ram Air. This seal glues to the lower Ram Air pan.
1968-74 Firebird, Trans Am; Aluminum Rear Carburetor Fitting; with Angled Fitting
Reproduction of the original carburetor rear fitting designed specifically for use with 1968-74 Pontiac Firebird and Trans Am models with 326, 350, 400, and 455 motors with or without Ram Air. This fitting screws to the back...
1972-74 Firebird, Trans Am; Aluminum Carburetor Fitting; with 2 Angled Fittings
Reproduction of the original aluminum carburetor fitting designed for use with 1968-75 Pontiac models including Firebird and Trans Am. Each fitting features the correct GM part number # 487331 stamped on the part for...
1968-75 Firebird, Trans Am; Carburetor Rear Fitting; with Straight Fitting
Reproduction of the original aluminum carburetor fitting designed for use with 1968-75 Pontiac models including Firebird and Trans Am. This particular fitting was used on most all 1968-69 Firebird models, but can also be used...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...