1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van ...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
1965-67 GM; Fuel Tank Sending Unit; 3/8"
The most accurate reproduction fuel tank sending unit in the industry, with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original....
Reproduction carburetor to accelerator lever cable for 1970 Camaro (4 bbl), 1971-73 Camaro with (350 4 bbl.), and 1970-72 Chevelle (with 396, 454). Each cable is manufactured to correct length and specifications. Replaces...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1957-69 Buick, 1968-70 Chevrolet; Vented Gas Cap; with Markings
Reproduction GM gas cap that includes the correct "S" rivet and properly engraved markings. Manufactured and designed from the original OEM cap, the quality and materials are manufactured to exact specification with the "show...
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; without Pick-Up Tube; 0-90 Ohm
Universal fuel tank sending unit for various GM and other models that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...
1968-72 Chevrolet Chevelle, Malibu; Big Block; Quadrajet; Accelerator/Throttle Cable
Replacement accelerator/throttle cable for 1968-72 Chevrolet Chevelle and Malibu models. This cable is 23.5 inches long and is for big block applications. GM#'s 396454, 3972679. {specs}
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reproduction of the original fuel tank mounting straps designed for use with various 1973-77 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured with high strength corrosion-resistant stamped steel to factory...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x .060"...
Reproduction of the original fuel tank designed for use with 1973-77 Buick Regal and GM A-Body models as listed. Each fuel tank is manufactured to correct factory specifications featuring original dimensions and correct...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...