1968-79 Various GM applications; Rear End/Differential; Yoke Kit
This is the bolt and strap style yoke and includes bolts and straps. This yoke replaces GM # 3879208 and uses the 1330 U joint. Fits various 68-79 GM application including Chevelle, Cutlass and Camaro models with 12 bol...
1965-72 Various GM Vehicles; Rear End/Differential Cover; Aluminum W27; 12 Bolt; C Clip Style
New reproduction aluminum W27 12 bolt differential cover. These covers are made in the USA. It fits various 1965-72 GM vehicles including GTO, Chevelle, Skylark, rear ends with 12 bolt pattern. Fits all hardtop and...
1982-96 Camaro/Firebird/Impala//Chevy Truck; Chrome Differential Cover; 10-Bolt
Add a dash of flash to the underside of your truck with this high-quality chrome differential cover. Reproduction 10 bolt differential cover manufactured in quality stamped steel with polished chrome plating. Designed for use...
1956-72 GM; Rear End Cover Pipe Plug; 1""-14; Posi-Traction
Reproduction positraction differential fill plug for vehicles equipped with either a 10 bolt or 12 bolt positraction differential. This plug will replace the old or worn out original. This is the rear end pipe plug with 1"-14...
1958-64 Impala / Full Size Rear Axle Flange Gaskets
Replacement gaskets for the rear axle flanges on your 1958-64 full size. Set includes 2 gaskets.
1967 Camaro / Firebird Rear Axle Bumper
Reproduction rear axle bumper mounts on inner wheelhouse on all 1967 Camaro and Firebird models. Attaches to the body to prevent the rear axle from bottoming out. Sold individually. 2 required per vehicle.
1965-79 GM; Rear End Cover Pipe Plug; 3/4""; Posi-Traction
Reproduction positraction differential fill plug for vehicles equipped with either a 10 bolt or 12 bolt positraction differential. This plug will replace the old or worn out original. This is the hard to find 3/4" rear end...
1968-69 Camaro / Firebird Rear Axle Bumper with Bracket; RH
Reproduction of the original rear axle bumper and bracket for 1968-69 Camaro and Firebird models. This bumper is necessary to keep the your rear axle from hitting the rear frame rails when the rear suspension is fully...
1968-69 Camaro / Firebird Rear Axle Bumper with Bracket; LH
Reproduction of the original rear axle bumper and bracket for 1968-69 Camaro and Firebird models. This bumper is necessary to keep the your rear axle from hitting the rear frame rails when the rear suspension is fully...
Lower Control Arm Bumper / Rear Axle Bumper
Replacement rear axle bumper / lower control arm bumper for models listed below. 1962-67 Chevy II/Nova rear axle bumper. 2 required. 1963-87 Chevrolet/GMC Truck lower control arm bumper. 2 required.
This is a heavy duty center support bearing designed for longer-lasting service life for high-performance applications to support the center of the driveshaft assembly. Manufactured from machined and polished billet aluminum...
1967-72 Chevrolet, GMC Truck C10; Crossmember; Rear Axle; For Coil Springs; OE Style
Reproduction of the original rear axle crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame on coil spring trucks. A good way to replace a damaged crossmember on a rusty or...
1955-89 Chevy, GMC Truck, 1958-64 Impala Bel Air; Drive Shaft Support Cushion Bearing; OE Style
Correct reproduction of the original drive shaft support cushion bearing specifically designed for 1955-89 Chevrolet and GMC trucks that came with 2 piece drive shafts. The center support bearing is surrounded by a rubber...
1968-69 Camaro, Firebird; Rear Axle Bumper; Each
Reproduction of the original rear axle bumper for 1968-69 Camaro and Firebird models. This bumper is necessary to keep the your rear axle from hitting the rear frame rails when the rear suspension is fully compressed. For use...
1964-87 GM; Differential Cover Bolt; 5/16" x 1"
Original factory style bolt used to attach the differential cover to the differential on models with either a 10 bolt or 12 bolt rear end and features the correct original head markings. Each bolt has the correct "RBW" on the...
1971-2002 GM; Rear Axle Ventilator; Various Models; Reproduction; For .452 Hole
Reproduction of the original style rear axle ventilator designed for use with various 1971-2002 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models as listed. Each ventilator is manufactured in quality injection...
1953-2010 GM; Rear Axle/Transmission Ventilator; for 3/8" Hole
OER® reproduction of the ventilator used by GM on a multitude of applications from the 1950s thru todays cars and trucks including the rear axle housing, automatic transmissions. front transfer case on 4 x 4 models and...
Reproduction rear axle compression bumper which attaches to the body and keeps the rear axle from bottoming out. Manufactured using hard rubber material with molded in stud for mounting. This is the second design bumper that...
1955-57 Chevrolet Rear Axle Bumper, Each
Reproduction of the original rear axle bumper designed for use on 1955-57 Chevrolet car models. Manufactured from molded rubber to factory specifications for originality. Mounts on the axle housing. Sold individually. 2...