1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
1985-92 Camaro, Firebird; Fuel Tank Sending Unit
After years of use, your fuel sending unit can corrode. Its float can flood, and it can simply stop working, causing your fuel gauge to read incorrectly or even not at all. This Delco Service Replacement will replace your...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; without Pick-Up Tube; 0-90 Ohm
Universal fuel tank sending unit for various GM and other models that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...
1982-92 Camaro, Firebird; Fuel Tank Filler Neck
The original GM tank on 1982-92 models suffered from an inherent flaw at the neck joint, and were recalled back-in-the-day for leaking around the solder joint, which was prone to cracking at the seam. Our reproduction fuel...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x .060"...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1982-92 Camaro, Firebird; Fuel Filler Neck Pocket Sleeve
Reproduction of the original style fuel filler neck pocket sleeve designed for use with all 1982-92 Camaro and Firebird models. Each sleeve is anufactured in injection-molded ABS to correct factory specifations offering an...
Electric Fuel Pump; with Cadmium Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...
Electric Fuel Pump; with Cadmium Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...
1982-92 Camaro, Firebird; Fuel Tank Filler Door
Reproduction fuel tank filler door for all 1982-92 Camaro & Firebird models as listed below. This fuel tank door is manufactured in injection molded ABS and replicates the original design, appearance, and fitment. Offered in...
1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; w/o Pick-Up Tube; 0-30 Ohm
Universal fuel tank sending unit for various GM and other models that require a 30 ohm sender. Designed for use with OE or aftermarket 0-30 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...