Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1978-88 Regal, Cutlass, Grand Prix, G Body; T Top Repair Panels; 8-Piece Set; Stainless Steel
Reproduction inner t-top repair panel set for 1978-88 Buick, Chevrolet, Oldsmobile, and Pontiac G-Body models, produced in stainless steel for longevity. Stamped to factory specifications, for a proper fit. Comes in an...
1978-88 G-Body Windshield Glass Without Antenna
Reproduction windshield glass for 1978-88 G-Body models. Manufactured to factory specifications, featuring correct contours, and thickness. Band at the top of the glass is blue/green colored. Windshield is made without...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
1978-85 Regal, Monte Carlo, Cutlass; Back Window Glass; 2-Door Coupe; With Defrost; Tinted
Reproduction of the original back window glass for various GM G-Body 2 door coupe models equipped with rear window defroster. Manufactured with the proper shape, curvature, and pattern in tempered glass.
1984-87 Buick, Chevrolet, GMC, Oldsmobile, Pontiac; Windshield Wiper Motor; 2 Terminal; Brand New
Brand New Reproduction wiper motor built using the industry?s most advanced engineering technology. Core shortages and low availability have made our brand new replacement wiper motors the high quality, low cost alternative...
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
1980-2000 Buick, Chevrolet, GMC, Olds, Pontiac: Front Door Latch; LH Drivers Side; Various Models
OER® Authorized reproduction of the original front door latch designed for use with 1980-2000 models. Door latch is manufactured to correct factory specifications and replaces the old or worn out original exactly. Will...
1978-85 GM T Top Handle Set; Chrome; Pair
OER® reproduction of the original T-Top handles designed for use on various 1978-85 GM vehicles. Manufactured in quality die-cast zinc featuring a bright polished chrome finish. T-Top handles are used to secure and release...
1978-88 Various GM Models; Trim Cover; T-Top Inner Plastic Cover; Non Locking; RH; Black
Replacement T-Top inner plastic trim cover/molding non locking style for various 1978-88 GM Applications, including Buick Regal, Chevrolet Monte Carlo, Pontiac Grand Prix. Each panel is manufactured in injection-molded ABS...
U-Nut; M6 - 1.0; Panel Range .030" to .160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160") Specifications: OE #: 11503957 Quantity: Individual...
1978-87 Regal, G-Body; Upper Door Hinge; LH; EDP Coated
Reproduction of the original upper door hinge designed for use with various 1978-87 GM G-Body models as listed below. Each door hinge is manufactured in quality stamped steel to OE specifications. Includes roller detent, and...
1978-87 Regal, G-Body; Upper Door Hinge; RH; EDP Coated
Reproduction of the original upper door hinge designed for use with various 1978-87 GM G-Body models. Each door hinge is manufactured in quality stamped steel to OE specifications. Includes roller detent, and spring assembly....
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1978-88 Buick Regal, GM A Body; Hood Hinge Assembly; RH; EDP Coated; Various Models
Reproduction of the original hood hinge assembly designed for use with 1978-88 GM A and G Body models. Each hood hinge is manufactured in stamped steel to original factory specifications featuring correct dimensions for an...
1978-87 Regal, G-Body; Lower Door Hinge; RH or LH; Each; EDP Coating
Reproduction of the original lower door hinge designed for use with various 1978-87 Regal and GM G-Body models. Each door hinge is manufactured in quality stamped steel to OE specifications. All hinges come EDP coated for...