1983 Chevrolet Truck Parts - Electrical & Wiring

The OER Smart Charger 800 battery charger and maintainer for classic cars and trucks provides high frequency automatic intelligent charging for 12V lead-acid, flooded, or sealed maintenance-free (AGM and Gell Cell) batteries....

Add an additional 12V power outlet to your vehicle with a universal fit 12 volt power outlet assembly with cover. The plastic cover prevents dirt and moisture from entering the socket. This dependable source of 12V power,...

The OER Smart Charger 1250 battery charger and maintainer for classic cars and trucks provides high frequency automatic intelligent charging for 6V or 12V lead-acid, flooded, or sealed maintenance-free (AGM and Gell Cell)...

This OER® Authorized wiring harness set upgrades the stock headlamp wiring on your vehicle to provide your new bulbs with maximum power and decrease the chance of overloading the stock wiring and connectors. Power will...

Universal fit headlamp switch for a wide variety of vehicle applications from the 1940's and beyond. Each switch features 3 position push/pull functionality with knob and shaft. Required a 3/8 diameter hole for mounting, and...

Reproduction of the hard-to-find switch to replace original inoperative headlamp switch on 1976-78 Chevette. This reproduction switch will fit exactly as original and is designed as a service replacement for original GM part...

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...

Service replacement turn signal switch for various 1969-88 GM models. Located in the steering column this switch will aid in the prevention of accidents by warning other vehicles that you intend to turn. Fits a wide variety...

A hot exhaust manifold can cause serious damage to your electrical system. If not properly fastened, the wiring harness leading to your alternator/generator or other wiring harnesses could fall into an open area between the...

This OER® Authorized wiring harness set upgrades the stock headlamp wiring on your vehicle to provide your new bulbs with maximum power and decrease the chance of overloading the stock wiring and connectors. Power will...

Authentic looking reproduction turn signal switches for various 1977-83 models without tilt. Switches are accurate reproductions that feature the correct hazard knob, wiring harness and plugs for OE functionality and...

Replacement dash mounted windshield wiper switch for 1978-83 truck models not equipped with pulse wipers. Restore the function of your wipers by replacing the faulty original switch. Replaces OE # 14028807, 459481. Chevrolet...

Reproduction of the original style turn signal switch designed for use on various 1977-83 Chevrolet and GMC truck models without tilt steering wheel. Each turn signal switch is manufactured to correct factory specifications...

Replace your inoperative fuel tank selector switch with this quality reproduction. Each switch will replace the original exactly. Be sure to check your fuel selector switch whenever departing on a long journey. Chevrolet...

Replace the inoperative power door lock switch and enjoy the convenience of power door locks once again. This reproduction power door lock switch is just what you need to get your factory door lock working again. Fits left...

This is an OER® Authorized reproduction brake light switch. Activated by the brake pedal arm, this switch causes the rear lamps to illuminate when the brakes are applied. Applications: 1982-85 Buick Regal without Cruise...

OER® reproduction of the original headlamp mounting switch nut designed for use with various 1968-82 GM models. Manufactured to factory specifications, this headlamp switch mounting nut is used to retain the headlamp...

Original style alternator brackets for your classic. For use on vehicles with small block engine. Applications: 1976-79 Buick Skylark 1976-86 Chevrolet Camaro 1978-86 Chevrolet/GMC C/K Series Truck 1987-89 Chevrolet R/V...

Reproduction of the original style main and auxiliary battery tray and support designed for 1981-86 Chevrolet and GMC pickup trucks and 1981-91 Blazer, Jimmy, and Suburban models. Manufactured to OE factory specifications...

Chrome alternator bracket set for your classic. For use on vehicles with small block engine. 2 piece. Top bracket bolts to intake manifold. Applications: 1976-79 Buick Skylark 1976-86 Chevrolet Camaro 1978-86 Chevrolet/GMC...

Beautiful chrome upper alternator bracket with stylized holes for 1976-86 Chevrolet small block engines. For use with long water pump models equipped with an aftermarket intake manifold and/or headers. Hardware not included. ...

Reproduction turn signal switch for various GM models. Located in the steering column, this switch features the correct color-coded wiring and plastic connector for a plug-in installation. Replaces GM part #'s 1995906,...

Reproduction 7-terminal headlamp switch for a wide variety of 1969-96 GM models. This switch mounts on the dash and controls the flow of electrical current to the headlamp system. Each switch comes without the knob or shaft,...

Chrome reproduction of the hard to find original big block upper alternator bracket for use with factory intake manifolds. This bracket is designed for use with long water pumps on models equipped with an original big block...

Reproduction of the original style relay designed for use on various GM models. The relay was used for various years and applications including horn, power trunk lid and power antenna. The relay is considered an aftermarket...

Replacement single terminal door jamb switch designed for use on various models. Replace the old, damaged or non working door jamb switch with this quality service replacement. The door jamb switch will get your interior...

Replace your original inoperative stop lamp switch with this OER® Authorized replacement stop lamp switch. Note: This switch is a service replacement part that may not match the original switch cosmetically. However,...

Replace the inoperative ignition switch in your classic American vehicle with this quality OER® Authorized reproduction. Each switch is produced with a stamped steel bracket and injection-molded plastic connector that...

Replacement ignition switch for 1967-72 Chevrolet and GMC model vehicles with pre-installed lock cylinder and keys for your convenience. Replaces GM part numbers 1116683, 1116695, 1116704, 1116709, 1116711, 1116712. An...

Replace the inoperative ignition switch in your GM or AMC vehicle with this OER® Authorized reproduction. Each switch is produced with a stamped steel bracket and injection-molded plastic connector that gets mounted to...

OER® reproduction of the original oil pan battery cable clip designed for use on various GM models. Manufactured in stamped steel with a plastic coating that protects the cable. Installs between the oil pan bolt and the...

The headlight dimmer switch is located on the drivers front floor and is used to switch the headlights from low beam to high beam. This OER® Authorized reproduction switch is correct for all models which include a floor...

This is an OER® Authorized reproduction brake light switch. Activated by the brake pedal arm, this switch causes the rear lamps to illuminate when the brakes are applied. Applications: 1973-74 Buick Apollo - all Models...

An oil pressure sending unit is an electrical or mechanical sensing device that sends information to the pressure warning lamp. Camaro applications: 1967-85 5.0-H, 1 terminal Firebird applications: 19 68-76 6 cyl. all 1977...

Manufactured with die-cast and billet aluminum. This new high performance gear reduction starter weighs only 10 lbs.! Fits small block and big block Chevy V8 models with 153 and 168 tooth flywheels, standard or automatic...

This hose clip is designed to secure a pair of heater hoses to the inner fender skirt to prevent damage of the hoses and keep the engine compartment neat and tidy in appearance. These were original equipment on a variety of...

Manufactured with die-cast and billet aluminum. This new high performance gear reduction starter weighs only 10 lbs! Fits small block and big block Chevrolet V8 models with 153 and 168 tooth flywheels, standard or automatic...

Quality reproduction of the original horn assembly designed for use with various 1958-96 Buick, Chevrolet, and Pontiac models. Each horn is manufactured to factory specifications replicaing the original in quality, fitment...

Due to the corrosive nature of battery electrolyte, the original lead cast positive and negative terminal ends usually require replacement every few years. We offer this replacement OEM type terminal for use on side terminal...

Due to the corrosive nature of battery electrolyte, the original lead cast positive and negative terminal ends usually require replacement every few years. We offer these replacement OEM type terminals for use on top post...

This all new high torque small case starter is just what you?ll need if you have a built engines with headers. For Chevy small block or big block engines when header clearance is a problem. 168 teeth, staggered mounting

*Penny Shipping! For a limited time, this item ships for only $0.01 (one cent) to any address within the contiguous USA. Order NOW and $AVE! *Note: Applicable shipping fees may be required on additional items added to the...

This OER® Authorized wiring harness set upgrades the stock headlamp wiring on your vehicle to provide your new bulbs with maximum power and decrease the chance of overloading the stock wiring and connectors. Power will...