1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
1978-81 Chevrolet Corvette; Fuel Tank Sending Unit; With Dual 1/4", 3/8" Outlets; Stainless Steel
Reproduction fuel sending unit for 1978-81 Chevrolet Corvette. Each sending unit is manufactured in stainless steel to correct factory specifications to replace the old, or non working original exactly. This is a dual 1/4"...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; without Pick-Up Tube; 0-90 Ohm
Universal fuel tank sending unit for various GM and other models that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x .060"...
1978-82 Chevrolet Corvette; Fuel Tank; Zinc Coated; 24 Gallon Capacity
Reproduction fuel tank for 1978-1982 Chevrolet Corvette models. Each fuel tank is manufactured in quality stamped steel to original factory dimensions featuring a heavy zinc coating for corrosion resistance. Includes a 18...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Cadmium Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...
Electric Fuel Pump; with Cadmium Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...
1978-82 Chevrolet Corvette; Fuel Tank Straps; Stainless Steel; Pair
Reproduction fuel tank mounting straps for mounting the gas tank in 1978-1982 Corvette models. Manufactured to factory specifications from upgraded stainless steel materials for longer lasting corrosion resistance. Sold in...
1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; w/o Pick-Up Tube; 0-30 Ohm
Universal fuel tank sending unit for various GM and other models that require a 30 ohm sender. Designed for use with OE or aftermarket 0-30 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...
1978-1982 Chevrolet Corvette; Fuel Tank Mounting Straps; EDP Coated Galvanized Steel
Reproduction of the original fuel tank mounting straps for use with 1978-1982 Chevrolet Corvette models. Each strap is manufactured in stamped steel to original to factory specifications. Features zinc plating with a black...