1970-81 Camaro / Firebird; Side Hood Rubber Stopper
Correct replacement hood rubber stopper including correct configuration and design. Manufactured in rubber material same as original. Sold individually. 4 required per vehicle.
1970-81 Firebird Rubber Stopper Kit
Achieve a clean appearance by replacing the rubber stoppers. The stoppers can wear out and cause problems with the body panels. The stoppers will help keep your panels in the correct alignment positions.M The kit includes...
1958-85 Various GM Models; Black Billet Aluminum; Hood Adjustment; Bumpers: Pair
Replacement billet aluminum hood adjustment bumpers for various GM applications including Impala, Skylark, Tempest models. Replace the original rubber hood adjuster stoppers with a correctly configured black billet aluminum...
Rubber Floor Pan Plug; 1-1/4" Dia. Fits 1" hole.Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1968-81 Trunk Lid Bumper On Lid; 7/8" Diameter, 1/2" thick
Correct replacement bumper to eliminate the lid from touching the body and causing unnecessary damage. Dimensions: Body Diameter: 7/8" Body Height: 1/2" Mounting hole diameter: 7/32" Overall Height: 13/16" ...
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction of the original outer rear hood bumpers designed for use on various GM models as listed. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment....
1970-81 Firebird, Trans Am; Hood Rubber Bumper ; Each
Correct reproduction of the original rubber hood bumper designed for use on all 1970-81 Firebird models. Each bumper is manufactured in quality rubber compound to original specifications assuring a quality appearance and fit....
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction of the original hood adjustment bumpers designed for use on various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated,...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1962-81 GM; Glove Box Door Arm Rubber Bumper
OER® reproduction of the original glove box door arm rubber bumper designed for use with various 1962-81 GM models. This rubber bumper is manufactured in EPDM rubber to the original factory configuration. Was installed on...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1962-78 Nova, Camaro, Firebird, Impala, Truck; Speedometer Cable Firewall Grommet; w/Steel Insert
Quality reproduction of the original speedometer cable firewall grommet designed for use on various 1962-73 Chevy II Nova, Camaro, Impala, Bel Air, Biscayne, Caprice, Firebird, and 1973-78 Chevrolet, GMC truck models as...
1965-92 Outer Door Rubber Bumper; Various Models
Reproduction of the original rubber stopper designed for use on the upper door section of the various GM models listed below. Each rubber stopper is manufactured to replicate the original in fitment and appearance. This...
1970-87 Buick, Chevrolet, Olds, Pontiac; Control Arm Bumper; Upper; Various Models
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM rubber ensuring a quality reproduction...
Reproduction rear axle compression bumper which attaches to the body and keeps the rear axle from bottoming out. Manufactured using hard rubber material with molded in stud for mounting. This is the second design bumper that...