Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1970-81 Camaro, Firebird, Nova; "Bullet" Remote Outer Door Mirror; LH Drivers Side
Reproduction of the original remote outer door mirror designed for use on a variety of 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutless, 442, and more. Manufactured with a die-cast zinc outer body...
Replace the worn or rusted out rear floating bow or rear tacking rail with this quality reproduction. This 1-piece tack strip, also referred to as a trimstick mounts to the frame just behind the quarter glass and secures the...
1968-72 GM A-Body 2-Door Coupe Windshield Tinted With Antenna
OER reproduction glass for a variety of 1968-72 GM A-Body models with antenna in windshield. Features tinted laminated glass, no date coding, with antenna laminated between glass layers. Each windshield is professionally...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; Passenger Side; Various Models
This OER® reproduction door hinge will allow your door to work properly again! The 1970-81 doors were extremely heavy and hard on the original hinges. A new set of hinges will help your doors to open and close the way the...
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1968-72 GM A-Body; Convertible Top Hydraulic Hose Set; with Power Top; White Hose
Reproduction of the original hydraulic hose set designed for use with 1968-72 GM A body convertible models as listed. Finding an original hose for your early convertible is next to impossible. If you own a convertible model...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
1969-72 Oldsmobile, Cutlass, 442, F85; Hood Hinge LH(driver side) GM#403727
Reproduction factory style hood hinge for 1969-72 Oldsmobile Cutlass, 442, W30, W31 Rally 350 and F85 models. Replace the worn out hinge and get the proper hood alignment on factory steel or Ram Air hood. {specs}
Inside hood latch release handle cable with handle for various 1969-72 GM applications including, Oldsmobile Cutlass, Pontiac GTO models. It has a black housing with a chrome knob, border and lettering that mounts underneath...
Reproduction of the original hood hinge assembly designed for 1969-72 Cutlass, 442, W30, W31, Rally 350 models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the...
1971-73 Buick/Oldsmobile License Plate Holder Bracket
Reproduction license plate holder bracket to fit a variety of Buick and Oldsmobile models. Stamped steel with tension springs as original. Buick Applications: 1971-73 All models (except wagons) Oldsmobile...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...