Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...
1970-81 Camaro, Firebird, Nova; "Bullet" Remote Outer Door Mirror; LH Drivers Side
Reproduction of the original remote outer door mirror designed for use on a variety of 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutless, 442, and more. Manufactured with a die-cast zinc outer body...
Replace the worn or rusted out rear floating bow or rear tacking rail with this quality reproduction. This 1-piece tack strip, also referred to as a trimstick mounts to the frame just behind the quarter glass and secures the...
1971-72 Pontiac GTO, LeMans; Ram Air; Steel Hood Pan
This is the same upper hood pan that GM installed on 1971-72 GTO, and LeMans models. Replace the rusted or damaged or pan with this steel original style pan. {specs}
1968-72 GM A-Body 2-Door Coupe Windshield Tinted With Antenna
OER reproduction glass for a variety of 1968-72 GM A-Body models with antenna in windshield. Features tinted laminated glass, no date coding, with antenna laminated between glass layers. Each windshield is professionally...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
1969-72 Pontiac GTO, 1970-72 Oldsmobile Cutlass; Hood Release Cable & Latch Kit
Reproduction hood release latch and cable kit for 1968-70 Pontiac LeMans, 1968-72 GTO and 1970-72 Oldsmobile Cutlass and 1970-71 442 models. For applications that have inside hood release. This kit comes with both the cable...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; Passenger Side; Various Models
This OER® reproduction door hinge will allow your door to work properly again! The 1970-81 doors were extremely heavy and hard on the original hinges. A new set of hinges will help your doors to open and close the way the...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
1968-72 GM A-Body; Convertible Top Hydraulic Hose Set; with Power Top; White Hose
Reproduction of the original hydraulic hose set designed for use with 1968-72 GM A body convertible models as listed. Finding an original hose for your early convertible is next to impossible. If you own a convertible model...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1969-72 Oldsmobile, Cutlass, 442, F85; Hood Hinge LH(driver side) GM#403727
Reproduction factory style hood hinge for 1969-72 Oldsmobile Cutlass, 442, W30, W31 Rally 350 and F85 models. Replace the worn out hinge and get the proper hood alignment on factory steel or Ram Air hood. {specs}
1970-71 Oldsmobile 442, 1970-72 Cutlass, F85; Hood Release Latch
Hood primary hood release latch for 1970-71 Oldsmobile 442 and 1970-72 Cutlass and F85 models. This latch is designed for use with applications that have and inside hood release cable. This latch mounts to the radiator core...
Inside hood latch release handle cable with handle for various 1969-72 GM applications including, Oldsmobile Cutlass, Pontiac GTO models. It has a black housing with a chrome knob, border and lettering that mounts underneath...