1971 Buick Stage 1 GS 350, GS 455; Trunk Emblem; BY BUICK Nameplate
Reproduction "BY BUICK" nameplate emblem for the trunk lid on 1971 Buick GS 350 and GS 455 Stage 1 models. Each die-cast emblem is designed and manufactured to replicate the original for an authentic appearance and fit....
1964-72 Buick, Skylark, Gran Sport, GS; Console Emblem; 4-Speed Shift Pattern
Reproduction 4-speed shift pattern emblem for the floor-mounted center console in various 1964-72 Buick A-Body models with manual transmission and console. Each console emblem has the R, 1, 2, 3, 4 shift pattern with the...
Speed Nut for 1/8" Stud - Self Threading - 8 Piece Set - with Rubber Pad
OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 1/8" stud. This speed nut can be applied to virtually any emblem or product that has a 1/8" stud and pressed into the...
Speed Nut for 1/8" Stud - Self Threading - 4 Piece Set; with Rubber Pad
OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 1/8" stud. This speed nut can be applied to virtually any emblem or product that has a 1/8" stud and pressed into the...
Speed Nut for 3/16" Stud - Self Threading - with Rubber Pad; 4 Piece Set
OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a 3/16" stud and pressed into...
1967-1974 "GM Mark Of Excellence" Door Deflector Decal; Embossed; Blue; Each
Reproduction of the original "GM Mark of Excellence" door reflector decal original installed on many various 1967-74 General Motors vehicles. It is used as a reflector to allow upcoming traffic to see the car door when...
1970-72 Buick GS, Front Fender Emblem; Stage 2
Reproduction fender emblem nameplate with "STAGE 2" insignia for 1970-72 Buick GS models. If you are lucky enough to have one of the extremely rare 1970 Stage 2 models, this is the emblem for the front fender to designate the...
1964-89 GM; Rear Axle ID Tag; Various Models
Reproduction of the original limited slip rear axle ID tag mainly used to ensure thew right gear oil is added to the rear end. This tag was mainly used with 1964-89 GM models indicating the correct lubrication requirement....
1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated
OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...
Barrel Nut, Fits 1/8" Emblem Stud, Fits 11/64" Hole, White Nylon
Replacement barrel nuts used on various GM vehicles. The barrel nut or tubular nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation....
Speed Nut 1/4" Self Thread Cutting - 12 Piece Set
Speed nuts are a great way of installing parts with studs onto the vehicle. These speed nuts are applied to the stud and pushed into the hole. The part is held in place by the self threading nut. 12 piece speed nut set is...
Push On Flat Nut, Fits 3/32" Stud, Black Phosphate Coated, 10 Piece Set
Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...
Push On Flat Nut, Fits5/16" Stud, Black Phosphate Coated, 10 Piece Set
Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...
Barrel Nut, Fits 1/8" Emblem Stud, Fits 1/4" Hole, Spring Steel, Phosphate Coated, 10 Piece Set
Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...
Thread Cutting Nut, 1/8" Stud Size, 1/4" Hex, 10 Piece Set
Replacement thread cutting pal-nuts used on various GM vehicles. Hex head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware...
Thread Cutting Nut, 1/8" Stud Size, 5/16" Hex, 10 Piece Set
Replacement thread cutting pal-nuts used on various vehicles. Hex head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware...
Speed Nut 3/16" Self Thread Cutting - Small Washer - Each
OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or part that has a 3/16" stud and pressed into the...
Barrel Nut, Fits 1/8" Emblem Stud, Fits 11/64" Hole, White Nylon, 10 Piece Set
Replacement barrel nuts used on various GM vehicles. The barrel nut or tubular nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation....
Barrel Nut, Fits 1/8" Emblem Stud, Fits 5/32" Hole, Spring Steel, Phosphate Coated, 10 Piece Set
Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...
Barrel Nut, Fits 1/8" Emblem Stud, Fits 3/16" Hole, Spring Steel With Sealer, 10 Piece Set
Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...