1970-74 Plymouth Barracuda; Wheel Opening Molding Set; Front and Rear; 4 Piece Set; Made In USA
Reproduction of the original wheel opening moldings designed for use with 1970-74 Plymouth Basrracuda models. Each molding is manufactured to correct factory specifications resulting in an authentic appearance when installed....
1970-74 Barracuda, Cuda; Rear Tail Molding Set; 3 Piece Set
Reproduction of the original rear tail panel 3-piece "M88 deck molding treatment" set for 1970-71 Barracuda Gran Coupe and "deck lid molding treatment" for 1972-74 Barracuda and 'Cuda models . Each molding set is manufactured...
1966-76 Ford/Dodge/Plymouth; Molding Clip; For Windshield / Rear Window Upper Reveal Molding; Each
Factory-style replacement windshield and rear window upper reveal molding clip for various vehicles. This steel clip measures 3/4" x 11/16". Sold individually. Note: For set of 12 pieces, refer to item # HK525. ...
1970-74 Barracuda, Cuda, Challenger; Trunk Lid Molding Hardware Set; with 3 Piece Molding Set
Reproduction of the original hardware designed to install the trunk lid molding for 1970-74 Mopar E-Body models. This hardware set is used to mount the 3-piece molding set that installs onto the deck lid and the rear quarter...
1968-76 Dodge/Plymouth/1964-68 Ford; Windshield Push On Molding Clip Kit; 24 Pieces
Reproduction windshield molding clips for a variety of classic American car models including, but not limited to 1968-76 Dodge, Plymouth A, B, E-Body models and 1964-68 Ford Mustang coupe and fastback models. These clips are...
1970-74 Coupe Barracuda; Door and Quarter Top Edge Molding Set ; 4 Piece Set; Anodized Aluminum
Factory-style reproduction of the original door and quarter panel top edge moldings for 1970-74 Plymouth Barracuda models. Molding attaches to the outer door and quarter panel and runs horizontally along the entire length....
1970-71 Barracuda, Cuda; Tail Panel Molding and Hardware Kit
Factory-style reproduction of the original tail moldings designed for use with 1970-71 Barracuda and Cuda models. Sold as a complete kit, these moldings mount to the rear tail panel. Designed and manufactured to factory...
1970 Cuda Rocker Moldings Fish Gill
"Fish Gill" rocker moldings mount underneath each door and run from the fender to the quarter panel. Manufactured of fiberglass and plastic composite, and feature correct contours with finish. Although original for 1970 'Cuda...
1970-71 Barracuda, Cuda; Tail Panel Molding Set; 4 piece Set
Reproduction of the original rear tail panel 4-piece molding set for 1970-71 Barracuda and 'Cuda models (except Gran Coupe). Each molding is manufactured in stamped aluminum to original factory specifications. Includes the...
Premier reproduction windshield reveal molding clip set for Challenger and Barracuda models. This factory-style replacement front window reveal molding clip is manufactured in steel to replace the broken, cracked or rusted...
Reproduction phillips head screw for attaching the wheel openig moldings and various reveal molding clips to the window channel of the vehicle. Each screw comes with a wax sealant at the tip of the screw to seal the hole from...
1970-74 Dodge, Plymouth E-Body; Rear Window Molding Alignment Clip: With Wax Tip Sealing Screw
Premier reproduction of the metal alignment clip used to attach the rear window moldings on 1970-74 Dodge and Plymouth E-Body models. This is the 2" long stamped steel clip. Comes finished in the proper phosphate and red dye...
Nylon Tail Molding Clip; 1/2" Long, White Nylon; Requires #8 Tapping Screw
Tailgate molding clips for 1966-67 Chevrolet Full Size Wagon and Chevrolet Malibu, Chevelle Wagon models, and El Camino. Nylon clip replaces OE # 4490167. Sold individually.
1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated
OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...
Molding Clip Stud Screw; #4 x 3/8" with 1/8" Shoulder; Zinc Plated
Replacement mounting screw for attaching molding clips to the body, Commonly used for: door ledge, window reveal, rocker panel and quarter panel molding retainers. Also used to replace welded stud posts that might be missing....
1960-72 Chevrolet, GMC Truck; Wire Tail Molding Clip, #10-24, 4" Long, Zinc Plated, 10 Piece Set
Reproduction of the original style wire tail molding clip used on various 1960-72 Chevrolet and GMC trucks. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...
Wire Tail Molding Clip, #8-32, 3/4" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24, 2-1/2" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24 With Sliding Stud, 1-5/8" Long, Zinc Chromate, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Molding Clip, Push In, 1-1/4" With Top Tension Spring, 10 Piece Set
Replacement metal tail style push in molding clips used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...