Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1955-82 Spare Tire Hold Down Nut
OER® reproduction of the original wing nut designed for use on many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct...
1969-70 Full-Size Chevrolet 4 Door Sedan & Station Wagon Tinted Windshield Glass With Antenna
Replacing your original damaged or missing windshield glass will enhance your vehicle?s appearance and safety by allowing you to see clearly. Don?t settle for anything less than original quality glass when replacing the...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
1969-81 GM; Door Hinge Repair Set ; Except with 15mm OD Bushings
Reproduction of the original door hinge components for use on various GM models. Repair the broken door hinges with this comprehensive repair set. Each repair kit includes 4 properly hardened shoulder pivot pins and 8...
1968-79 Camaro, Impala, Nova; Rear License Plate Bracket; with Hinge
Reproduction rear license plate bracket for various 1968-79 GM models. Manufactured in stamped steel to factory specifications for an authentic appearance. The door features a spring action hinge that allows access to the gas...
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
Correctly reproduced glass windshield washer bottle with a screen printed screw on cap with antifreeze/windshield washer fluid lettering. Each bottle is manufactured in the correct factory configuration that replaces the old...
Original style replacement outer door mirror for 1968-72 models, features convex glass. The convex glass helps eliminate the passenger side blind spot. Each rear view mirror features the correct ribbed base and comes with a...
1947-79 GM; Various Models; Chrome Drop Mount Peep Mirror; LH Or RH; 4"
OER® Authorized reproduction drop head mirror for 1941-79 GM model cars and trucks. Early style drop head mirror mount to top edge of door frame. Features a chrome arm with a 4 inch mirror head. Fits sedan and truck...
1970 Impala, Bel Air, Caprice Chevelle, El Camino; Hood Hinge; LH Passenger Side; EDP Coated
Reproduction of the original hood hinge assembly designed for use on various 1970 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
U-Nut; M6 - 1.0; Panel Range .030" to .160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160") Specifications: OE #: 11503957 Quantity: Individual...
1969-70 Front Outer Door Handle Set - 2 Door - Impala / Full Size Models
Quality reproduction of the original outer door handle set designed for use on 1969-70 Impala and Full Size models. Each door handle set is manufactured in zinc die-cast metal and includes a high quality triple chrome plating...
1969-70 Rear Outer Door Handle Set - 4 Door - Impala and Full Size Models
Quality reproduction of the original outer door handle set designed for use on 1969-70 Impala and Full Size models. Each door handle set is manufactured in zinc die-cast metal and includes a high quality triple chrome plating...