1964 Impala, Bel Air, Biscayne; Outer Grill Eyebrow Moldings; RH and LH; Pair
Reproduction of the original front fender lower eyebrow (outer grill) moldings designed for use on 1964 Chevrolet Impala, Bel Air, and Biscayne models. Each molding is a replication of the original GM eyebrow molding found on...
1962-64 Impala Roof Drip Rail Moldings; Hardtop; 2 Door Models; Pair
Reproduction of the original roof drip moldings designed for use with 1962-64 Chevrolet Impala, Bel Air, and Biscayne models. Each molding is manufactured in stamped aluminum to OE specifications and will replace the old,...
1964 Impala Standard Rear Cove Quarter Panel Extension Molding - LH
Reproduction of the original rear cove quarter panel extension molding designed for use on 1964 Impala and Full Size Chevrolet models with standard trim level. Molding is stamped correctly in quality aluminum material for an...
1964 Impala Standard Rear Cove Quarter Panel Extension Molding - RH
Reproduction of the original rear cove quarter panel extension molding designed for use on 1964 Impala and Full Size Chevrolet models with standard trim level. Molding is stamped correctly in quality aluminum material for an...
Original style capped stud and clip nut designed to protect the owner from accidently cutting hands when reaching into areas like the trunk where the rear panel and quarter molding clips could cause harm. Most commonly used...
1964 Chevrolet Bel Air, Biscayne, Impala; Front Hood Lip Molding; with Emblem & Hardware
Reproduction front hood lip molding & emblem for 1964 Chevrolet Impala, Bel Air, and Biscayne passenger car models. Each molding is stamped from high grade aluminum duplicating the original GM molding in every detail for an...
1964 Impala / Full Size Center Rear Cove Molding - Standard Models
Reproduction of the original rear cove center panel molding designed for use on 1964 Impala and Full Size Chevrolet models with factory standard trim level. Each molding is stamped from quality aluminum material in the...
1964 Impala / Full-Size Center Hood Split Molding
Reproduction of the original Impala, Bel Air and Biscayne center hood split molding for 1964 models. This hood split molding runs down the center of the hood and sections off the RH from the LH sides of the hood. Each molding...
1964 Impala SS, Bel Air, Biscayne; Upper Trunk Lid Molding; Except Station Wagon
Reproduction of the original upper trunk molding designed for use with 1964 Impala SS, Bel Air, and Biscayne models. Each molding is manufactured in bright finished stamped aluminum replicating the original contour and...
1964 Impala SS, Bel Air, Biscayne; Outer Tail Cove Moldings; Pair
Reproduction of the original outer tail cove moldings designed for use with 1964 Impala SS, Bel Air and Biscayne models. Each molding is manufactured in bright finished stamped aluminum replicating the original contour and...
Reproduction phillips head screw for attaching the wheel openig moldings and various reveal molding clips to the window channel of the vehicle. Each screw comes with a wax sealant at the tip of the screw to seal the hole from...
Nylon Tail Molding Clip; 1/2" Long, White Nylon; Requires #8 Tapping Screw
Tailgate molding clips for 1966-67 Chevrolet Full Size Wagon and Chevrolet Malibu, Chevelle Wagon models, and El Camino. Nylon clip replaces OE # 4490167. Sold individually.
1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated
OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...
1960-72 Chevrolet, GMC Truck; Wire Tail Molding Clip, #10-24, 4" Long, Zinc Plated, 10 Piece Set
Reproduction of the original style wire tail molding clip used on various 1960-72 Chevrolet and GMC trucks. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...
Wire Tail Molding Clip, #8-32, 3/4" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24, 2-1/2" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24 With Sliding Stud, 1-5/8" Long, Zinc Chromate, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Molding Clip, Push In, 1-1/4" With Top Tension Spring, 10 Piece Set
Replacement metal tail style push in molding clips used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...
Metal Universal Break Off Style Molding Clip, #10-24 Thread, 2.5" Wide, Zinc Plated, 10 Piece Set
Replacement break off style molding clips used on various vehicles. These clips are designed to be trimmed the width of the molding, features pre-scribed break off/cut off grooves. #10-24 nuts sold separately. Each clip...
Wire Tail Molding Clip, #10-24, 1" Long, Zinc Chromate (Gold Iridescent), 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...