1964 Impala, Bel Air, Biscayne; Outer Grill Eyebrow Moldings; RH and LH; Pair
Reproduction of the original front fender lower eyebrow (outer grill) moldings designed for use on 1964 Chevrolet Impala, Bel Air, and Biscayne models. Each molding is a replication of the original GM eyebrow molding found on...
1962-64 Impala Roof Drip Rail Moldings; Hardtop; 2 Door Models; Pair
Reproduction of the original roof drip moldings designed for use with 1962-64 Chevrolet Impala, Bel Air, and Biscayne models. Each molding is manufactured in stamped aluminum to OE specifications and will replace the old,...
1962-64 Impala, SS, Bel Air; Back Glass Molding Clip Set
OER® reproduction of the original back window reveal molding clips set designed to fit 1962-64 Impala and Super Sport models 2 door hardtop models. This set of clips will replace the old, damaged or worn out originals and...
1963-64 Impala, Bel Air; Windshield Molding Clip Set; 2 Door Hardtop
OER® reproduction of the original windshield reveal molding clips set designed to fit 1963-64 Impala and Super Sport models 2 door hardtop models. This set of clips will replace the old, damaged or worn out originals and...
1964 Impala; Bel Air; Trunk Split Molding Clip Set
The correct hardware can make a great difference in the finished look or your restoration. When mounting or replacing the trunk center split molding on your 1964 Impala or Bel Air model, use the correct clips for a proper...
Original style capped stud and clip nut designed to protect the owner from accidently cutting hands when reaching into areas like the trunk where the rear panel and quarter molding clips could cause harm. Most commonly used...
1964 Chevrolet Bel Air, Biscayne, Impala; Front Hood Lip Molding; with Emblem & Hardware
Reproduction front hood lip molding & emblem for 1964 Chevrolet Impala, Bel Air, and Biscayne passenger car models. Each molding is stamped from high grade aluminum duplicating the original GM molding in every detail for an...
1964 Impala / Full-Size Center Hood Split Molding
Reproduction of the original Impala, Bel Air and Biscayne center hood split molding for 1964 models. This hood split molding runs down the center of the hood and sections off the RH from the LH sides of the hood. Each molding...
1964 Impala, Bel Air; Trunk Center Molding; Trunk Spear; with Hardware
Reproduction of the original Chevrolet Impala or Bel Air center trunk split molding designed for use on 1964 models. This center trunk molding runs down the center of the trunk lid and sections off the RH from the LH sides....
1964 Impala SS, Bel Air, Biscayne; Upper Trunk Lid Molding; Except Station Wagon
Reproduction of the original upper trunk molding designed for use with 1964 Impala SS, Bel Air, and Biscayne models. Each molding is manufactured in bright finished stamped aluminum replicating the original contour and...
1964 Impala SS, Bel Air, Biscayne; Outer Tail Cove Moldings; Pair
Reproduction of the original outer tail cove moldings designed for use with 1964 Impala SS, Bel Air and Biscayne models. Each molding is manufactured in bright finished stamped aluminum replicating the original contour and...
1964 Impala SS; Bel Air; Lower Trunk Lid Molding
Reproduction of the original lower trunk molding designed for use with 1964 Bel Air, and Impala SS models. Each molding is manufactured in stamped aluminum replicating the original contour and factory design. Will replace the...
1964 Impala SS; Bel Air; Inner Tail Cove Moldings; with Hardware; Pair
Reproduction of the original inner tail cove moldings designed for use with 1964 Impala SS and Bel Air models. Each molding is manufactured in stamped aluminum replicating the original contour and factory design. Will...
Reproduction phillips head screw for attaching the wheel openig moldings and various reveal molding clips to the window channel of the vehicle. Each screw comes with a wax sealant at the tip of the screw to seal the hole from...
Nylon Tail Molding Clip; 1/2" Long, White Nylon; Requires #8 Tapping Screw
Tailgate molding clips for 1966-67 Chevrolet Full Size Wagon and Chevrolet Malibu, Chevelle Wagon models, and El Camino. Nylon clip replaces OE # 4490167. Sold individually.
1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated
OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...
Molding Clip Stud Screw; #4 x 3/8" with 1/8" Shoulder; Zinc Plated
Replacement mounting screw for attaching molding clips to the body, Commonly used for: door ledge, window reveal, rocker panel and quarter panel molding retainers. Also used to replace welded stud posts that might be missing....
1960-72 Chevrolet, GMC Truck; Wire Tail Molding Clip, #10-24, 4" Long, Zinc Plated, 10 Piece Set
Reproduction of the original style wire tail molding clip used on various 1960-72 Chevrolet and GMC trucks. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...
Wire Tail Molding Clip, #8-32, 3/4" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24, 2-1/2" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...