Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1961-64 Impala, LeSabre, Electra, Catalina; Convertible Top Header Bow
Reproduction of the original convertible top header bow designed for use with various 1961-64 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac B-body full size models as listed. Each header bow is manufactured to factory...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
1961-1977 Various Buick Vehicles; Trunk Accessory/Auxiliary Mat; GM# 981403
Reproduction OEM accessory rubber trunk mat with Buick shields logo for 1961-77 Buick models including Skylark, Electra and Riviera. This is an auxiliary mat that goes on top of the felt covering. This is an officially...
Reproduction of the original hydraulic hose set designed for use with a wide variety of convertible models as listed. Finding an original hose for your early convertible is next to impossible. If you own a convertible model...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Windshield Wiper Blades; Aero Style; 15"; for 1/4" (7mm) Bayonet Style Arms; Pair; Various Models
High quality reproduction of the stainless steel "Aero" Anti Wind-Lift Wiper Blades designed to fit 7mm wide bayonet style wiper arms. Popularized in the 1960's and 70's to combat wind lift at high speeds, these 15 inch wiper...
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction of the original upper door hinge designed for use on 1961-64 Impala, Bel Air, Biscayne, and GM B-Body models. Sagging and worn door hinges can cause damage to doors, locks and hinge pillar sheet metal. Why go...
1961-65 GM Full Size; Vent Window Regulator; Passenger Side; GM B Body Models
Reproduction of the original vent window requlator designed for use on various 1961-65 GM Buick, Chevrolet, Oldsmobile, and Pontiac full size models. Each regulator is designed and manufactured to replicate the original in...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1958-80 TRICO RF-15 Style Wiper Blade Refill; 15" Length; Reproduction; Various Models
OER® reproduction of the original Trico RF-15 wiper blade insert/refill for 15" TRICO wiper blades. This period-correct TRICO RF-15 style insert is made with a stainless steel vertebra and a precision wiping edge produced...
Correctly reproduced glass windshield washer bottle with a screen printed screw on cap with antifreeze/windshield washer fluid lettering. Each bottle is manufactured in the correct factory configuration that replaces the old...
U-Nut; M6 - 1.0; Panel Range .030" to .160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160") Specifications: OE #: 11503957 Quantity: Individual...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...