1962 Impala, Biscayne, Bel Air; Hood Lip Molding; with Chevrolet lettering; GM Licensed
Reproduction of the original hood lip molding designed for use with 1962 Impala, Bel Air, and Biscayne passenger car models. Each molding is stamped from high grade aluminum replicating the original molding for an authentic...
1962-64 Impala, 1962 Bel Air; Rear Back Glass Molding Set; 2 Door, Hardtop; 5 Piece Set; OER
OER® reproduction of the original back glass molding set designed for use on 1962 Bel Air 2 door hardtop, 1962-64 Impala, and Impala SS, 2-door hardtop models. Each set of back glass moldings is designed to replace the...
1962-64 Impala Roof Drip Rail Moldings; Hardtop; 2 Door Models; Pair
Reproduction of the original roof drip moldings designed for use with 1962-64 Chevrolet Impala, Bel Air, and Biscayne models. Each molding is manufactured in stamped aluminum to OE specifications and will replace the old,...
1962-64 Impala, SS, Bel Air; Back Glass Molding Clip Set
OER® reproduction of the original back window reveal molding clips set designed to fit 1962-64 Impala and Super Sport models 2 door hardtop models. This set of clips will replace the old, damaged or worn out originals and...
1962 Impala; Tail Panel Cove Moldings; with Hardware; Pair
Correct reproduction of the original tail lamp cove moldings for 1962 Impala and Full size Chevrolet models. These polished aluminum moldings attach to the quarter panel and act as an extension of the trunk lid molding....
1962 Impala, Bel Air; Upper Trunk Lid Molding; with Clips
Reproduction of the upper trunk lid molding designed for use on 1962 Impala and Bel Air Chevrolet models. Trunk lid molding fits on the rear upper section of the trunk lid. Each molding is contoured and stamped in quality...
Original style capped stud and clip nut designed to protect the owner from accidently cutting hands when reaching into areas like the trunk where the rear panel and quarter molding clips could cause harm. Most commonly used...
Reproduction phillips head screw for attaching the wheel openig moldings and various reveal molding clips to the window channel of the vehicle. Each screw comes with a wax sealant at the tip of the screw to seal the hole from...
Nylon Tail Molding Clip; 1/2" Long, White Nylon; Requires #8 Tapping Screw
Tailgate molding clips for 1966-67 Chevrolet Full Size Wagon and Chevrolet Malibu, Chevelle Wagon models, and El Camino. Nylon clip replaces OE # 4490167. Sold individually.
1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated
OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...
Molding Clip Stud Screw; #4 x 3/8" with 1/8" Shoulder; Zinc Plated
Replacement mounting screw for attaching molding clips to the body, Commonly used for: door ledge, window reveal, rocker panel and quarter panel molding retainers. Also used to replace welded stud posts that might be missing....
1960-72 Chevrolet, GMC Truck; Wire Tail Molding Clip, #10-24, 4" Long, Zinc Plated, 10 Piece Set
Reproduction of the original style wire tail molding clip used on various 1960-72 Chevrolet and GMC trucks. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...
Wire Tail Molding Clip, #8-32, 3/4" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24, 2-1/2" Long, Green Dip Coated, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Wire Tail Molding Clip, #10-24 With Sliding Stud, 1-5/8" Long, Zinc Chromate, 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Molding Clip, Push In, 1-1/4" With Top Tension Spring, 10 Piece Set
Replacement metal tail style push in molding clips used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...
Metal Universal Break Off Style Molding Clip, #10-24 Thread, 2.5" Wide, Zinc Plated, 10 Piece Set
Replacement break off style molding clips used on various vehicles. These clips are designed to be trimmed the width of the molding, features pre-scribed break off/cut off grooves. #10-24 nuts sold separately. Each clip...
Wire Tail Molding Clip, #10-24, 1" Long, Zinc Chromate (Gold Iridescent), 10 Piece Set
Replacement wire tail molding clips used on various GM vehicles. Nuts sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This...
Nylon Tail Push In Molding Clip, 1-3/8" Long, White Nylon, 10 Piece Set
Replacement nylon tail style push in molding clips used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...
Molding Clip Retaining Pal Nut, #10-24 Thread Size, 1/2" Diameter Washer Head, 10 Piece Set
Replacement molding clip retaining pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or...