Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1961-64 Impala, LeSabre, Electra, Catalina; Convertible Top Header Bow
Reproduction of the original convertible top header bow designed for use with various 1961-64 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac B-body full size models as listed. Each header bow is manufactured to factory...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...
Reproduction of the original convertible top cylinder designed for use with 1961 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile full size convertible models. All convertible top cylinders are not the same. This...
1961-62 GM Models; Vent Assembly With Clear Glass; LH; 2 or 4 Door Hardtop
This reproduction vent assembly comes with vent frame, new glass, and is completely assembled ready to install. This is a nice and easy way to replace your vent glass and frame at the same time.
1961-62 GM Models; Vent Assembly With Clear Glass; RH; 2 or 4 Door Hardtop
This reproduction vent assembly comes with vent frame, new glass, and is completely assembled ready to install. This is a nice and easy way to replace your vent glass and frame at the same time.
1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1961-62 Impala, Bel Air, GM Hardtop and Convertible; Vent Window Frame; LH
/li> 1961-62 Pontiac Applications: Catalina; Jobs 2337, 2347, Bonneville; Jobs 2537, 2847, Grand Prix; Jobs 2837, 2947 2 Door Hardtop Catalina, Bonneville, Star Chief; Jobs 2339, 2639, 2839, 2539 4 Door Hardtop ...
1961-64 Impala, GM 2 Door Hardtop and Convertible; Door Window Channel; Lower; LH
Reproduction lower window channel that allows the replacement of the often rusted channel where the glass installs. The door window glass rests in the channel assembly as it mounts to the regulator. For the LH side. Fits...
Correctly reproduced glass windshield washer bottle with a screen printed screw on cap with antifreeze/windshield washer fluid lettering. Each bottle is manufactured in the correct factory configuration that replaces the old...
U-Nut; M6 - 1.0; Panel Range .030" to .160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160") Specifications: OE #: 11503957 Quantity: Individual...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction of the original side door vent glass designed for various 1961-62 GM models including Chevrolet, Buick, Cadillac, Pontiac and Oldsmobile. Each glass is authentic reproduction offering a quality fit and...
16" Windshield Wiper Blade Refill; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
Reproduction of the original side door vent glass designed for various 1961-62 GM models including Chevrolet, Buick, Cadillac, Pontiac and Oldsmobile. Each green tinted glass is authentic reproduction offering a quality fit...