Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1970-81 Camaro, Firebird, Nova; "Bullet" Remote Outer Door Mirror; LH Drivers Side
Reproduction of the original remote outer door mirror designed for use on a variety of 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutless, 442, and more. Manufactured with a die-cast zinc outer body...
Reproduction convertible top motor engineered to deliver consistent hydraulic pressure and dependable operation. This unit makes it easy to raise and lower your power top by replacing a weak or worn out original. Each motor...
1966-67 Pontiac Tempest, Lemans, GTO; Front Bumper; Chrome
Reproduction front bumper for 1966-67 Tempest, Lemans, GTO models. Each bumper is manufactured to OE factory specifications and features a bright chrome polished finish. {fitment}
1968-69 Pontiac GTO; Front Bumper Brackets; w/Endura bumper; Hide Away Head Lamps
Correct reproduction of the original bumper brackets for use with 1968-69 Pontiac GTO models with Endura bumper and hideaway head lamps. Each bracket is manufactured in stamped steel to the same configuration as the factory...
1964-65 Chevelle, GM A-Body; Convertible Top Header Bow
Reproduction convertible top header bow for various 1964-65 Buick, Chevrolet, Oldsmobile, and Pontiac A-body mid size models. Each header bow is manufactured to factory specifications replicating the original in design,...
Reproduction convertible top motor made to deliver consistent hydraulic pressure and dependable performance. Allows smooth raising and lowering of the power top. Each motor includes rubber mounts and features original style...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1963-67 Chevrolet, Oldsmobile, Pontiac; Hood Hinge Assembly; RH Passenger Side
Reproduction hood hinge assembly for various 1963-67 GM models. Each hood hinge is manufactured from stamped steel to factory specifications assuring a quality replacement. Features correct mounting points for ease of...
Replace the worn or rusted out rear floating bow or rear tacking rail with this quality reproduction. This 1-piece tack strip, also referred to as a trimstick mounts to the frame just behind the quarter glass and secures the...
1966-67 Buick, Chevy, Olds, Pontiac; Lower Door Hinge Detent Set; 4 Piece Set
Reproduction of the original lower door hinge roller and bolt for use with 1966-67 Buick Special, Pontiac GTO, Lemans, Tempest 1967 Camaro, Firebird, and other various models as listed. The rollers are manufactured in quality...
1973-77 Regal; Cutlass; Monte Carlo; El Camino; LeMans; Body Mount Bushing Set; 28 piece
Reproduction 28 piece body mount bushing set for various 1973-77 GM models. Manufactured to factory specifications for proper fitment and function. These kits are made out of compression molded S.B.R. with steel sleeve...
1966-1967 Camaro, Firebird, F85, GTO, LeMans; Upper Door Hinge; RH or LH; Each
Reproduction upper door hinge for various Buick, Chevrolet, Pontiac, and Oldsmobile models including 1967 Camaro and Firebird. Each hinge is manufactured in heavy steel for durability and dependability. Sold individually. 2...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...