1961-02 GM; Inner / Outer Door Handle Bumper
Reproduction door handle bumper manufactured to factory specifications from correct rubber material to fit and function as original. This rubber bumper is designed to protect the sheet metal of the door where the outer door...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
1982-04 GM; Hood Adjustment Bumper and Bolt; 1" Diameter Rubber Stopper
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1968-81 Camaro, Impala, Firebird; Door Glass Guide Stop Bumpers; Pair; Various GM
Reproduction of the original door glass guide stop bumpers designed for use with various 1968-81 General Motors vehicles. These glass guide stops are required for proper door glass alignment. Commonly damaged during removal...
1993-98 Camaro / Firebird Fuel Filler Door Rubber Bumper
Reproduction of the fuel tank filler door rubber bumper for all 1993-98 models. This bumper attaches on the fuel filler pocket. Sold individually. 2 required. You are assured that every part offered is manufactured to exact...
Reproduction of the rubber bumper to fit a variety of GM models and applications. Sold individually. Refer to detailed applications below. Buick Applications- For Door Pull Handles: Regal 1991-92 - rear door Skylark 1986-91 -...
1987-15 GM; Trunk Lid Drain Hole Plug; 9/16" Overall Diameter; Fits 5/16" Hole
Reproduction trunk lid drain hole plug for 1987-2015 GM vehicles including 1991-96 Impala and Caprice models. Manufactured from molded rubber as original, these install on the underside of the trunk lid. Measures 9/165"...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1963-90 GM; Rubber Bumper; Various Applications
Reproduction rubber bumper for various GM applications. Each bumper is manufactured in EPDM rubber to factory specifications replicating the original in design and fitment. This bumper was used for various applications as...
1954-1981 Hood Adjustor Bumper and Stud - Various GM vehicles
Reproduction 5/16-18 x 1-1/2" hood bumper. Includes correctly threaded stud with a 1" diameter x 1/2" tall round rubber top. Helps keep the hood aligned when installed. Can be adjusted higher or lower. 2 hood adjust bumpers...
1958-72 GM; Trunk Lid Rubber Stopper; Each; Buick, Chevy, Olds, Pontiac; Various Models
Correct OER® reproduction of the original trunk lid rubber bumpers designed for use with various 1960-72 GM models. Manufactured to factory specifications including correct stud to adjust for height concerns. Eliminates...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper;Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM rubber ensuring a quality reproduction...
1982-93 Glove Box Door/Ashtray Bumper
Reproduction of the anti-rattle rubber bumper for the glove box door on 1982-85 Impala and 1982-93 Caprice models and for the ash tray on 1990 Caprice models. Measures 5mm in height and fits a 3mm hole. 2 required per...