1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1967-74 GM; Control Arm Ball Joint; Upper
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1964-74 GM; Lower Ball Joint; Various Models; RH or LH
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1962-67 Chevy II Nova; Upper Control Arm; with Ball Joint and Bushing; LH or RH
Reproduction upper control arm, shaft and ball joint assembly for 1962-67 Chevrolet Chevy II/Nova and Pontiac Acadian models. Each control arm assembly is manufactured in quality stamped steel to the factory configuration...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4" to 4" inclusive. These heat treated washers are for general purpose and structural use. For use...
1970-81 Camaro, Firebird, 1975-79 Nova; Rear Leaf Spring Installation Set; Multi-Leaf
Reproduction of the original and complete rear leaf spring installation kit designed for use on 1970-81 various GM vehicles equipped with multi-leaf rear springs including 1970-81 Camaro, Firebird, 1975-79 GM X-body models as...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...