1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Reproduction of the original style fuel tank designed for use with 1975-76 Impala, Bel Air, and Caprice station wagon models (except 2 and 4 door coupe models). Each fuel tank is manufactured in quality stamped steel and zinc...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Reproduction fuel tank for carbureted gasoline or diesel powered 1977-1990 Impala, Caprice, Buick, Oldsmobile, and Pontiac models. This fuel tank is manufactured in zinc-coated stamped steel to original factory...
Reproduction of the original style fuel tank designed for use with 1980-1990 Impala, Caprice, Buick, Oldsmobile, and Pontiac Full Size models as listed except station wagon. This fuel tank is manufactured in zinc-coated...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Reproduction fuel tank mounting strap set for various 1977-1988 Buick, Chevrolet, Pontiac, and Oldsmobile full size models as listed (except station wagon). Each strap is manufactured in quality stamped steel, galvanized and...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1974-81 Outer Accelerator Pull Spring
Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction of the original style fuel tank designed for use with 1970-74 Impala, Bel Air, Biscayne, Catalina, Bonneville and GM full size station wagon models. This fuel tank is made of zinc-coated steel and has a capacity...
Reproduction of the original style fuel tank designed for use with 1968-70 Impala, Bel Air, Biscayne, Catalina, Bonneville station wagon models. This fuel tank is made of zinc-coated steel and has a capacity of 22 gallons (91...
1977-79 Impala / 1977-80 GM Full Size (Except Wagon); Fuel Tank With Neck; 19 Gallon; Niterne
Reproduction of the original fuel tank for 1977-79 Impala/Caprice and various GM Full Size models except station wagon. Manufactured in authentic niterne steel. Note: Shipped Truck Freight. Chevrolet Applications: 1977-1979...