1970-81 Camaro, Firebird, GM X-Body; Side Hood Rubber Stopper; Each
Correct reproduction of the original hood rubber stopper for use with 1970-81 Camaro & Firebird models. Each stopper is manufactured in quality EPDM rubber and features the correct configuration and design. Sold individually....
1962-77 Buick, Chevrolet, Pontiac, Oldsmobile, A, X Body; Trunk Weatherstrip; Various Models
This reproduction trunk weatherstrip is designed for a wide variety of GM models and is a great solution for replacing worn, cracked, or flattened original trunk seals that can allow water, dust, and exhaust fumes into the...
OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
Reproduction of the original door frame weatherstrip that installs on the outer frame of the door on 1965-66 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile Full Size 2 door hardtop or convertible models. Manufactured in...
1963-64 Impala, Electra, Wildcat; Door Frame Weatherstrip Seal; 2-Door Hardtop; Convertible, Pair
Quality reproduction of the original door frame weatherstrip that installs on the outer frame of the door on 1963-64 Impala and GM full size 2 door hardtop and convertible models. Manufactured in the correct configuration...
Exact reproduction of the original door frame weatherstrip that installs on the outer frame of the door on 1961-62 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile full size passenger car models. Manufactured in the...
Reproduction back glass weatherstrip seal designed for various GM 2-door hardtop models including 1962-64 Impala, and Buick, Oldsmobile, and Pontiac 2-door pillarless coupe (non-post) cars. Will not fit sedan models with...
Reproduction of the original trunk weatherstrip manufactured in the correct configuration. Prevent water damage in your trunk area by replacing the worn and damaged weatherstrip with this authentic reproduction. The soft...
Replace your trunk weatherstrip and stop leaks which could cause severe damage and rust to your trunk pan and entire trunk area. Keep your trunk area water tight and completely sealed when closed ensuring the trunk pan is...
1961-2002 Buick, Chevy, Pontiac, Oldsmobile; Inner & Outer Door Handle Bumper; Each; Various Models
Reproduction door handle bumper manufactured to factory specifications from correct rubber material to fit and function as original. This rubber bumper is designed to protect the sheet metal of the door where the outer door...
Exact reproduction of the original door frame weatherstrip that installs on the outer frame of the door on 1961-62 Buick, Chevrolet, Pontiac, and Oldsmobile Full-Size 2 door sedan models. Manufactured in the correct...
1937-80 GM, 1961-64 Impala, 1964-72 El Camino; Gas Door Bumpers; 1937-58 1-prong Door Bumpers; Pair
Correct reproduction rubber bumper for various GM applications. Fits: 1937-1958 GM full size vehicle door bumper, single prong style, front or rear. 1961-64 full size and 1964-72 El Camino gas filler door. Keeps the door from...
1969-70 Impala Custom, Caprice, LeSabre, Wildcat; Molded Roof Rail Weatherstrip; 2-Door Coupe; Pair
Correct reproduction of the original roof rail weatherstrips designed for use on 1969-70 Impala Custom/Caprice models. Eliminate water or other elements from entering the passenger area by replacing these essential seals....
Quality reproduction of the original roof rail weatherstripping designed for 1959-60 Impala and Full size GM models. This quality reproduction seals the area between the roof rail and the door glass eliminating water and...
Correct reproduction of the original roof rail weatherstrips designed for use on 1969-70 Impala 4 door hardtop models. Eliminate water or other elements from entering the passenger area by replacing these essential seals....
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1958-73 GM; Door Frame Weatherstrip Plug Set; 26 Piece Set
Reproduction weatherstrip clip receiver for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. 26 required per door. 52 required...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1993-2005 Camaro, Firebird, Grand Am; Console Door & Ash Tray Door Bumper; Each; Various Models
Correct reproduction of the original console door and console ash tray cover rubber bumper for 1997-2002 Camaro and Firebird models. Sold individually, use as required. Fitment Applications: 1997-2002 Camaro / Firebird...
1964-72 Buick, Chevrolet, Oldsmobile, Pontiac; Fuel Tank Vent Tube Grommet; Each
Replacement vent tube grommet for 1964-72 GM models. Manufactured to factory dimensions, this molded rubber grommet fits in the trunk pan and features two holes for the fuel vent tube to pass through.
1967-69 Camaro, Firebird, 1968-79 Nova; Front Door Bumper; Each
Correct replacement front door rubber bumper for 1967-1969 Camaro, Firebird, 1967-70 Impala, Full Size, 1968-79 Nova, X body 4 door models. Each bumper is replicated to the original OE specifications and fits the door...
1961-81 Buick, Chevy, Pontiac, Oldsmobile; Trunk Lid Rubber Bumper On Lid; Each; Various Models
Correct reproduction of the original trunk lid rubber bumper for use with various 1961-81 Buick, Chevy, Pontiac, and Oldsmobile models. Manufactured in EPDM rubber to factory specifications. Used to eliminate the trunk lid...
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1957-70 Buick, Cadillac, Chevy, Pontiac, Oldmobile; Trunk Weatherstrip; Various Full Size Models
Reproduction of the original trunk weatherstrip manufactured in the correct configuration. Prevent water damage in your trunk area by replacing the worn and damaged weatherstrip with this authentic reproduction. The soft...
1968-74 Nova, Apollo, Omega, Ventura; Rubber Stopper Set; 14 Piece Set
Reproduction of the original common rubber bumpers and stoppers used in 1968 Chevy II and 1968-72 Nova and X body models. Each stopper kit includes a variety of rubber bumpers and stoppers that will replace the commonly...
1969 Camaro, Firebird; 1968-74 Nova; Cowl Firewall Seal Set; 5 Piece Set; Made in the USA
Reproduction of the original style cowl firewall seals designed for use with 1969 Camaro, Firebird, 1968-72 Chevy II Nova, 1971-74 Pontiac Ventura, 1971 Acadia, 1973-74 Buick Apollo, and 1973-74 Olds Omega models. Replace the...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
Reproduction roof rail weatherstrip channel set for 1966-67 Chevrolet Chevelle, Pontiac GTO, Tempest, LeMans, Buick Skylark, Gran Sport, and Oldsmobile 442, Cutlass, and F85 2-door hardtop models. Manufactured to factory...
Reproduction roof rail weatherstrip channel set for 1964-65 Chevrolet Chevelle, Oldsmobile Cutlass, F85, and Buick Skylark 2-door hardtop models. Manufactured to factory specifications, this 6-piece stainless steel set...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
Correct reproduction of the original roof rail weatherstrips designed for use on 1965-66 Impala and Full Size GM 2 door hardtop models. Eliminate water or other elements from entering the passenger area by replacing these...
1968-81 Nova, Apollo, Omega, Phoenix, Ventura; Outer Door Rubber Stopper Set ; 4 piece set
Reproduction of the original style rubber bumpers designed for use on 1968-79 Chevy II, Nova, and GM X-body models. The rubber stoppers on your door will wear out or detereriate over time. These reproduction stoppers will...
Reproduction of the original style door frame weatherstrips designed for use with 1955-57 Chevrolet Bel Air, Pontiac Chieftain, Starchief, Oldsmobile, 88, and 1957 Bonneville two door hardtop and convertible models. Creates a...
Exact reproduction of the original door frame weatherstrip that installs on the outer frame of the rear door on 4 door Chevy II and Nova models. Manufactured in the correct configuration which allws easy installtion when...
1967-68 Impala / Full Size Quarter Window Weatherstrip, Convertible, Pair
Quality reproduction of the original weatherstripping designed for use on 1967-1968 Impala convertible models. Each strip is manufactured with OEM type rubber material for authenticity and fit. Installs vertically on the side...
1959-73 GM; Door Frame Weatherstrip Plug Set; 52 Piece Set
Reproduction weatherstrip clip receiver for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. 26 required per door. 52 required...
Reproduction roof rail weatherstrip channel connectors for 1968-72 Chevrolet Chevelle, Pontiac GTO, Tempest, LeMans, Buick Skylark, Oldsmobile 442, Cutlass, F85, and 1970-72 Chevrolet Monte Carlo 2-door hardtop models....
1987-04 GM, 1993-97 Camaro, Firebird; Hood Adjuster Bumper Cap; Each
Reproduction of the front hood adjuster bumper cap for 1993-97 Camaro, Firebird, and various other 1987-2004 GM models. Manufactured to correct factory dimensions in quality EPDM rubber for an authentic replacement. Sold...
1982-2012 GM Fuel Door; Door Pull Handle; Hood Stop; Sunroof. Rubber Bumper; Each; Various Models
Reproduction of the original style rubber bumper that fits a wide variety of 1982-2012 GM models and applications. Can be used for the fuel door, front and rear door pull handle, hood stop bumper, and sunroof control arm....
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1955-90 Buick, Chevrolet, Pontiac, Oldsmobile; Door Lock Gasket; Each; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...
1961-79 GM; Bucket Seat Back Rubber Stopper Set; Round; w/Mounting Screws; Pair
Reproduction of the original seat back rubber stoppers designed for use on various 1961-79 GM models. These rubber stoppers help prevent rattling and keep the seat back positioned correctly. Replace worn out or missing seat...
1964-79 Camaro, Chevelle, Firebird, Nova, X-Body; Outer Door Handle Gasket Set; Various Models
Reproduction of the original outer door handle gasket set designed to properly seal the exterior door handles on various classic vehicle applications. Each set includes precision die-cut gaskets manufactured to factory...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1955-1976 Glove Box Door Arm Rubber Stopper
Reproduction of the original glove box door arm rubber stopper designed for use on various GM models. Eliminate the rattling and looseness of the glove box door by simply replacing the worn out or missing rubber glove box...
1980-2016 GM; Outer Hood Adjust Rubber Bumper; Each; Various Models
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1976-92 Buick, Chevrolet, Oldsmobile, Pontiac; Trunk & Hatchback Weatherstrip Seal; 18 Foot Length
Reproduction weatherstripping designed to replace the cracked or damaged original for various GM models. This weatherstripping is manufactured exactly like the original unlike other weatherstrips on the current market....
Correct reproduction of the original U-shape rubber molded weatherstrip seal originally installed on 1969-70 Buick, Chevy, Pontiac, and Oldsmobile Full Size hardtop & convertible passenger car models. This seal attaches to...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
Reproduction of the original hood to cowl seal weatherstrip designed for use on 1991-96 Buick, Cadillac, Chevrolet, and Oldsmobile Full Size passenger car models. Each hood seal is manufactured from durable EPDM rubber in the...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1964-72 Chevrolet, Pontiac; Lower Control Arm Bumper; Each; Various Models
Reproduction of the original lower control arm bumper designed for use on various GM vehicles including 1968-1969 Camaro and Firebird models. Each bumper is manufactured from durable hard rubber and features the correct...
1962-70 Buick, Chevy; Pontiac, Oldsmobile; Control Arm Bumper; Rubber; Each; Various Models
Reproduction of the original control arm bumper designed for use on various GM models. Each bumper is manufactured to factory specifications in the correct configuration and includes a built in stud ensuring a perfect fit....
1962-81 Trunk Lock Cylinder Gasket ; Die-Cut Replacement
Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...
1975-79 Nova, Ventura, Apollo, Omega; Door Frame Weatherstrip; 2 Door; Coupe, Pair; OER
Reproduction of the original door frame weatherstrip installed on all 1975-79 Nova and GM X-body 2 door coupe models. Each weatherstrip is manufactured in quality EPDM rubber to the correct configuration and features the...
1951-72 Buick, Chevrolet, Pontiac, Oldsmobile; Convertible Power Top Motor Mounting Grommet; Each
Reproduction of the original rubber mounting/insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a damper...