Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1970-81 Camaro, Firebird, Nova; "Bullet" Remote Outer Door Mirror; LH Drivers Side
Reproduction of the original remote outer door mirror designed for use on a variety of 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutless, 442, and more. Manufactured with a die-cast zinc outer body...
1966-67 Oldsmobile Cutlass, 442, W-30; Inner Fender Skirt Wells; Red; Pair
Reproduction of the correc red W-30 plastic front inner fender well skirts for 1966-67 Oldsmobile Cutlass and 442 W-30 models. Manufactured with injection molded ABS plastic in red. These were used in place of the black steel...
1971-72 Pontiac GTO, LeMans; Ram Air Upper Hood Pan; Stamped Steel
Reproduction of the original steel hood pan for use with 1971-72 Pontiac GTO and LeMans models with Ram Air. This pan is manufactured in quality stamped steel and deigned for use with the rarre and optional Ram Air models....
Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...
1964-65 Chevelle, GM A-Body; Convertible Top Header Bow
Reproduction convertible top header bow for various 1964-65 Buick, Chevrolet, Oldsmobile, and Pontiac A-body mid size models. Each header bow is manufactured to factory specifications replicating the original in design,...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; Passenger Side; Various Models
This OER® reproduction door hinge will allow your door to work properly again! The 1970-81 doors were extremely heavy and hard on the original hinges. A new set of hinges will help your doors to open and close the way the...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
1969 Oldsmobile Cutlass, 442, F85; Radiator Grille; Black/Silver
High quality replacement front grilles for 1969 Oldsmobile Cutlass, 442 and F85 models. These grilles are made from high quality plastic and are silver and black. Replace broken, cracked or missing grille with these great...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
Replace the worn or rusted out rear floating bow or rear tacking rail with this quality reproduction. This 1-piece tack strip, also referred to as a trimstick mounts to the frame just behind the quarter glass and secures the...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
1964-72 GM Convertible Top Latch Knuckle Hook ; Each
Reproduction of the original latch knuckle hook designed for use on various GM converible models. The knuckle is used to hold the convertible top to the upper windshield header. Screws directly into the convertible top latch...