Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1979-81 Mustang, Capri; Fuel Tank; Zinc Plated; Before 4/81 Production Date; F82A
OER Authorized reproduction fuel tank for 1979-81 Mustang and Capri models (Prior to 4/81). Each tank is manufactured in quality stamped steel featuring a galvanized zinc coating for rust and corrosion resistance. This...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction fuel tank for 1981-86 Ford Mustang and Mercury Capri models. This reproduction fuel tank is manufactured in stamped steel featuring a Zinc coating for rust and corrosion prevention. Tank features a 15.4 gallon...
1984-85 Mustang, Capri; Fuel Tank Sending Unit; with Return Valve; 5.0L; with Manual Trans; Non-EFI
After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can cause your fuel gauge not to register properly or even send incorrect readings to the fuel gauge. Ensure that you...
1981-84 Mustang, Capri; Fuel Sending Unit; for Non-EFI; 5/16" w/ Return; Stainless Steel
After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can cause your fuel gauge not to register properly or even send incorrect readings to the fuel gauge. Ensure that you...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1966-69 Mercury Comet, Cyclone, Montego; Fuel Tank Filler Neck Pipe
Reproduction fuel filler neck pipe which connects with a fuel filler hose (sold separately) to the fuel tank. Replacing the filler neck is recommended whenever you replace your gas tank. This is where the gas cap attaches....
1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models
Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...
1979-81 Mustang, Capri; Fuel Tank Filler Pipe
Reproduction fuel filler neck for gas tank on 1979-81 Ford Mustang and Mercury Capri models buit on or before 04/01/1981. This reproduction fuel neck is manufactured in stamped steel featuring a protective coating against...
Reproduction fuel level sending unit for 1966-69 Ford Fairlane, 1968-69 Torino and 1966-69 Mercury Comet models with 3/8" inlet. This direct fit replacement includes the NBR float, locking ring, and O-ring. Does NOT fit...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction of the original style fuel tank designed for with 1987-97 Ford Mustang and 1983-86 Mercury Capri models. This reproduction fuel tank is manufactured in stamped steel featuring a Zinc coating for rust and...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...