1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van ...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1967-81 GM; Accelerator Pedal Pad Trim Plate; Stainless; Various Models
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb
Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1967-02 Accelerator Pedal Mounting Pin
This special mounting pin is just what you need to correct a loose accelerator pad. This special design allows the pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems commonly...
1955-69 Accelerator Pedal Firewall Bushings ; Pair
OER® reproduction of the original accelerator firewall bushings designed for use on various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive...
1964-71 GM; Various Models Floor Mounted Accelerator Pedal Pad Trim Plate
Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Each trim plate is manufactured in stamped stainless offering long lasting dependability and an authentic appearance. This...
1964-71 Chevrolet; Accelerator Pedal Pad w/Steel Insert ; Floor Mounted EPDM Rubber
Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...
1968-69 396 Carb to Accelerator Lever Rod ; Big Block with 4 bbl Carb
Reproduction of the original 1968-69 accelerator pedal rod designed for use with 396 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is...
1967-77 GM Pedal Pad Kit - Auto Trans - 6 Piece Kit
This complete kit is designed to replace pedal pads and trim plates on a variety of Chevrolet models including 1967-68 Camaro with drum brakes and an automatic transmission as well as a variety of additional GM models as...
1967-77 GM Pedal Pad Kit With Disc Brake Emblem; Auto Trans; 6-Piece Kit
Reproduction of the original pedal pads designed for 1967-68 Camaro, Firebird and a variety of additional GM models as listed. This pedal pad set is designed to replace the worn out original pads for models with disc brakes...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...
1968-81 GM Pedal Pad and Trim Plate Kit; Disc Brake; Auto Trans; 6 Piece Kit; Various Models
Reproduction of the original pedal pads and pedal pad trim plates to fit various GM models. This pedal pad set is designed to replace the worn out original pads for models equipped with disc brakes and automatic transmission....
1964-67 Accelerator Pedal Pad to Rod Support ; Stamped Steel ; Various Models
Reproduction of the original style stamped steel accelerator pedal pad to rod support unit. This steel reproduction is manufactured to replicate the original in appearance, design and functionality. Includes correct style...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...