1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1964-66 Chevrolet/GMC Truck, Suburban; Accelerator Pedal Pad
Reproduction accelerator pedal pad for 1964-66 Chevrolet and GMC trucks. Each accelerator pedal pad is manufactured in a plastic material to original specifications and features the correct original style waffle pattern at...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1960-63 Chevrolet/GMC Truck; Choke Cable; With Knob
Reproduction of the original choke cable designed for use with 1960-63 Chevrolet and GMC truck models as listed. Each cable is manufactured to factory specifications replicating the original in length and appearance offering...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1960-63 Chevrolet/GMC Truck; Throttle Cable; With Knob
Replace your original choke cable with this authentic reproduction throttle cable designed for use with 1960-63 Chevrolet and GMC truck models. The throttle cable mounts to the dash and offers reliable operation to the...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86 Chevrolet/GMC Truck 1965-70...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1947-66 Chevrolet/GMC Truck; 1955-57 Bel Air, 150, 210; Fuel Tank Sending Unit Screw Set
Reproduction of the original fuel tank sending unit screws and washers designed for use with 1947-66 Chevrolet, GMC trucks, and 1955-57 Bel Air, 150, 210, and Nomad models as listed. Each set features 5 phillips head screws...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...
Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevy Bel Air, 150, 210, Nomad, and 1931-62 Chevy and GMC pickup truck models. Correct replacement of the original fuel tank sending unit...