Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
1982-04 GM; Hood Adjustment Bumper and Bolt; 1" Diameter Rubber Stopper
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1970-77 Chevrolet El Camino, Monte Carlo, 1970-73 Chevelle; Hood Stop Stud; Pair
New hood stop studs for 1970-73 Chevrolet Chevelle and 1970-77 Monte Carlo that mount on cowl firewall. 2 are used per car. These lock the hood in back. Sold as pair only. These have the special head with "C". {specs}...
1987-2016 GM; Trunk Lid Drain Hole Plug; 9/16" Overall Diameter; Fits 5/16" Hole
Reproduction trunk lid drain hole plug for 1987-2016 GM vehicles including 1991-96 Impala and Caprice models. Manufactured from molded rubber as original, these install on the underside of the trunk lid. Measures 9/165"...
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set ; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1980-2016 GM; Hood Adjust Rubber Bumper; Outer Side; Each
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1955-72 GM; Lower Control Arm Bumpers; Polyurethane; Black; Pair
Polyurethane lower control arm bumper stops are guaranteed to last longer and perform better than O.E.M. rubber stops. Cushions impact between suspension components preventing excessive damage. Sold as a pair. 1 pair required...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1968-72 Lower Control Arm Bumper ; Each
Reproduction of the original lower control arm bumper designed for use on various GM vehicles including 1968-69 Camaro and Firebird models. Each control arm bumper is manufactured in hard rubber featuring correct mounting...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1966-1979 Camaro, Impala, Nova; Rubber Side Hood Bumper ; Each
Reproduction of the original style side hood rubber bumper designed for use various GM models. Over time, the rubber stoppers on your hood can wear out or deteriorate. These reproduction stoppers will help keep your hood...
1954-1981 Hood Adjustor Bumper and Stud - Various GM vehicles
Reproduction 5/16-18 x 1-1/2" hood bumper. Includes correctly threaded stud with a 1" diameter x 1/2" tall round rubber top. Helps keep the hood aligned when installed. Can be adjusted higher or lower. 2 hood adjust bumpers...
1968-96 Hood Rear Panel Bumper, Each, Various Models, Impala, Chevelle, Corvette
Reproduction of the original rear hood panel bumper designed for use on various 1968-96 GM models. Exact reproduction of the original rear hood bumper used to replace the worn out or missing original. Manufactured to exact...