This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1973-77 Chevelle, Regal, Cutlass, LeMans; 19 Gallon Fuel Tank; w/o Filler Neck;
Reproduction fuel tank for various 1973-77 GM A-Body models including Chevelle, Regal, Cutlass and LeMans. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion...
1970 Chevelle, Monte Carlo; 20 Gallon Fuel Tank; w/ Filler Neck; w/ Two Vent Pipes; w/o EVAP System
Reproduction fuel tank for various 1970 Chevrolet Chevelle and Monte Carlo models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion prevention. This is a 19...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
Reproduction fuel tank sending unit for 1968-70 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and 1970 Chevrolet Monte Carlo models. Manufactured to factory...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1973-77 Chevelle, Regal, Cutlass, LeMans; Fuel Tank Filler Neck; 13-1/4" Long, 2" Diameter
Reproduction of the original fuel tank filler neck designed for various 1973-77 GM A-Body models including Chevelle, Regal, Cutlass and LeMans models. Each neck is manufactured to factory dimensions and replaces the original...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reduce heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket and shield was original equipment for most 1970 Chevrolet...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
Reproduction of the original fuel tank mounting straps designed for use with various 1973-77 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured with high strength corrosion-resistant stamped steel to factory...
1974-81 Outer Accelerator Pull Spring
Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1970 Chevelle, Monte Carlo; 20 Gallon Fuel Tank; w/ Filler Neck; w/ Three Vent Pipes; w/ EVAP System
Reproduction fuel tank for various 1970 Chevrolet Chevelle and Monte Carlo models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion prevention. This is a 19...
1965-74 Holley; Carburetor Heat Shield; 4 Barrel with 396,454 Engine
OER® reproduction carburetor heat shield for all GM models with a Holley 4 bbl carburetor. This heat shield will help cool the intake charge for better performance. Original for 1970 396ci & 454ci with Special...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1970-72 Chevelle, El Camino, Monte Carlo, GTO, LeMans; 1970 Tempest; Accelerator Pedal Assembly
Reproduction accelerator pedal assembly for 1970-72 Chevelle, El Camino, Monte Carlo, GTO, and LeMans models, as well as 1970 Tempest. Manufactured to factory specifications, this assembly includes the pedal pad, mounting...
1973-77 GM A-Body; Fuel Tank Sending Unit; with A/C; 3-Lines; Regal, Century, Chevelle, Laguna
Reproduction of the original fuel tank sending unit designed for use with 1973-77 GM A-body models with 3/8" line. After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause your...
Reproduction of the original fuel tank sending unit for use with various 1973-77 Regal, Century, Chevelle, Laguna, Malibu, Monte Carlo, etc. models as listed. These sending units will replace the old or worn out original...
Reproduction fuel tank sending unit for 1978-88 Chevrolet Malibu, Monte Carlo, Buick Regal, Oldsmobile Cutlass, Pontiac Grand Prix, and Grand Am models. Manufactured to factory specifications, this sending unit accurately...
Reproduction fuel tank sending unit for 1978-88 Chevrolet Malibu, Monte Carlo, Buick Regal, Oldsmobile Cutlass, Pontiac Grand Prix, and Grand Am models. Manufactured to factory specifications, this unit accurately measures...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Reproduction fuel tank sending unit for 1971-72 Chevrolet Chevelle, El Camino, Monte Carlo, Pontiac GTO, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and GMC Sprint models. Manufactured to factory specifications, this...
Reproduction fuel tank sending unit for 1968-70 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and 1970 Chevrolet Monte Carlo models. Manufactured to factory...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Reproduction fuel tank sending unit for 1971-72 Chevrolet Chevelle, El Camino, Monte Carlo, Pontiac GTO, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and GMC Sprint models. Manufactured to factory specifications, this...
Reproduction fuel tank mounting straps for 1978-83 GM G-Body 2-door models produced using heavy-duty preformed steel that are black EDP coated to deter premature rusting. Straps are 37-3/8" long for 2-door models only. Fits...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1978-88 Buick, Chevrolet Pontiac, Olds; Accelerator Pedal Pad; Various Models
Reproduction of the original accelerator pedal designed for use on various 1978-87 GM G-Body models. Manufactured in injection molded ABS to factory specifications replicating the original in quality and appearance. Will fit...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1973-77 Chevelle, Regal, Cutlass, LeMans; Fuel Tank Strap Set; 35-1/2" Long; Stainless Steel; Pair
Reproduction of the original style fuel tank mounting straps for various 1973-77 GM A-Body models including Chevelle, Regal, Cutlass and LeMans models. Each strap is manufactured in quality stamped stainless steel for long...
1968-72 Chevrolet Chevelle, 1970-72 Monte Carlo; Small Block engines; Accelerator/Throttle Cable
Replacement accelerator cable for 1968-72 Chevorlet Chevelle and 1970-72 Monte Carlo models. Extends from the carburetor to the accelerator pedal lever. Sold individually. GM# 3973862.
1973-77 Chevelle, Regal, Cutlass, LeMans; Fuel Tank Strap Set; 35-1/2" Long; Zinc Coated Steel; Pair
Reproduction of the original style fuel tank mounting straps for various 1973-77 GM A-Body models including Chevelle, Regal, Cutlass and LeMans models. Each strap is manufactured in quality stamped steel and galvanized for...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1969-81 GM; Fuel and Brake Line Clip; Dual Line 3/8" & 1/4"; Each
This correct reproduction line clip is designed for securing fuel and brake lines to the frame on a variety of GM models. Manufactured from durable galvanized steel, this clip is engineered to accept one 3/8 inch and one 1/4...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
1967-78 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
1967-77 GM Pedal Pad Kit With Disc Brake Emblem; Auto Trans; 6-Piece Kit
Reproduction of the original pedal pads designed for 1967-68 Camaro, Firebird and a variety of additional GM models as listed. This pedal pad set is designed to replace the worn out original pads for models with disc brakes...
1968-72 Camaro, Impala, Nova; Quadrajet Throttle Cable Bracket
Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1967-77 GM Pedal Pad Kit - Auto Trans - 6 Piece Kit
This complete kit is designed to replace pedal pads and trim plates on a variety of Chevrolet models including 1967-68 Camaro with drum brakes and an automatic transmission as well as a variety of additional GM models as...
1974-78 Buick, Chevrolet, Oldsmobile, Pontiac; Cruise Control Cable Bracket
Cruise control cable bracket on carburetor, replaces GM # 342407. This bracket bolts it to accelerator cable bracket. It allows you to put 2 cables together when adding cruise control. This bracket is for cruise control cable...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6.