OER® reproduction of the original style rubber bumper designed for use with various GM applications. Each rubber stopper is manufactured to correct specifications in EPDM rubber ensuring long lasting quality. Will fit...
OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1937-80 GM, 1961-64 Impala, 1964-72 El Camino; Gas Door Bumpers; 1937-58 1-prong Door Bumpers; Pair
Correct reproduction rubber bumper for various GM applications. Fits: 1937-1958 GM full size vehicle door bumper, single prong style, front or rear. 1961-64 full size and 1964-72 El Camino gas filler door. Keeps the door from...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1958-73 GM; Door Frame Weatherstrip Plug Set; 26 Piece Set
Reproduction weatherstrip clip receiver for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. 26 required per door. 52 required...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1957-59 Chevrolet Speedometer Cable Grommet
This grommet mounts on the firewall where the speedometer cable runs through it. Manufactured in automotive grade molded rubber. Replaces OE # 3781684.
1958-59 Impala, Bel Air, Biscayne, El Camino; Rear Gas Filler Door Bumpers; Pair
Correct reproduction of the original gas filler door rubber bumper for use with 1958-59 Impala, Bel Air, Biscayne, and El Camino models. Each bumper is manufactured in EPDM rubber to original factory specifications. Keeps the...
1964-72 Buick, Chevrolet, Oldsmobile, Pontiac; Fuel Tank Vent Tube Grommet; Each
Replacement vent tube grommet for 1964-72 GM models. Manufactured to factory dimensions, this molded rubber grommet fits in the trunk pan and features two holes for the fuel vent tube to pass through.
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1955-57 Chevy Bel Air, 150, 210, Nomad; Upper Trunk lid, 1955-59 Rear License Plate Bumpers; Pair
Correct reproduction of the rubber bumper for the upper trunk on 1955-57 Chevrolet Bel Air, 150, 210, Nomad cars and the rear license plate on all 1955-59 Impala. Bel Air, Biscayne, El Camino, and station wagon models. Sold...
1982-04 GM; Hood Adjustment Rubber Bumper & Bolt; 1" Diameter; Each; Various Models
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1959-61 Impala, Bel Air, Biscayne; Hood Side Rubber Bumpers; Pair
Reproduction hood rubber bumpers for 1959-61 full size Chevrolet cars including Impala and Bel Air models. Designed to help keep your hood aligned and in the correct position. Each bumper duplicates the original and fits...
1955-81 Chevrolet, GMC, Pontiac; Air Cleaner Lid Rubber Seal; 59" Long x 5/16" Wide
Reproduction air cleaner lid seal for a variety of GM car and truck models as listed. Designed to seal the area between the lid and the base offering a tight seal for the air cleaner on models that required this seal.
1959-73 GM; Door Frame Weatherstrip Plug Set; 52 Piece Set
Reproduction weatherstrip clip receiver for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. 26 required per door. 52 required...
1959 Impala, Bel Air, Biscayne, Station Wagons; Hood To Grill Bumpers; Pair
Original style hood to grill rubber bumper for use on 1959 Chevrolet Impala, Bel Air, Biscayne, El Camino, and station wagon models. Manufactured using quality EPDM rubber, these bumpers are designed to keep the hood from...
1970-77 Chevrolet El Camino, Monte Carlo, 1970-73 Chevelle; Hood Stop Stud; Pair
New hood stop studs for 1970-73 Chevrolet Chevelle and 1970-77 Monte Carlo that mount on cowl firewall. 2 are used per car. These lock the hood in back. Sold as pair only. These have the special head with "C".
1960-61 Impala / Full Size Rear License Plate Bumpers - Pair
Correct reproduction rubber bumper for the rear license plate on 1960-61 full size Chevrolet cars including Impala, Bel Air and El Camino models. Sold as a pair.
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1955-90 Buick, Chevrolet, Pontiac, Oldsmobile; Door Lock Gasket; Each; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...
1964-79 Camaro, Chevelle, Firebird, Nova, X-Body; Outer Door Handle Gasket Set; Various Models
Reproduction of the original outer door handle gasket set designed to properly seal the exterior door handles on various classic vehicle applications. Each set includes precision die-cut gaskets manufactured to factory...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1966-72 GM; Outer Mirror Mounting Set ; LH or RH ; Gasket, Bracket, Screws
Reproduction of the original style components required to replace and mount the outer door mirror on the door. Contains all the necessary hardware to install a standard outer door mirror onto either the drivers or passenger...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1966-72 Chevrolet; Standard Door Mirror Gasket
Quality reproduction outer door mirror gasket for various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors. Installs between the mirror base and...
1955-1976 Glove Box Door Arm Rubber Stopper
Reproduction of the original glove box door arm rubber stopper designed for use on various GM models. Eliminate the rattling and looseness of the glove box door by simply replacing the worn out or missing rubber glove box...
1980-2016 GM; Outer Hood Adjust Rubber Bumper; Each; Various Models
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
Restore proper protection to your engine compartment with these factory-style OER reproduction splash apron flaps. Designed and manufactured to OE specifications, each apron set delivers an authentic fit and appearance while...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1964-72 Chevrolet, Pontiac; Lower Control Arm Bumper; Each; Various Models
Reproduction of the original lower control arm bumper designed for use on various GM vehicles including 1968-1969 Camaro and Firebird models. Each bumper is manufactured from durable hard rubber and features the correct...
1970-88 Buick, Chevrolet, Oldsmobile, Pontiac; Outer Door Handle Gasket; LH or RH; Each
Reproduction of the original outer door handle gasket designed for use with 1970-81 GM F-Body and 1973-88 GM G-Body models. This gasket installs on the backside of the exterior door handle to provide a protective barrier...
1962-66 Chevrolet; Door Rubber Bumper Set; 4 Piece Set; Various Models
Replacing the rubber door stoppers will help keep your doors aligned correctly while adding a factory fresh appearance to the vehicle. Each rubber bumper is designed and manufactured to exact OE specs. Manufactured in quality...
1962-81 GM; Glove Box Door Arm Rubber Bumper
OER® reproduction of the original glove box door arm rubber bumper designed for use with various 1962-81 GM models. This rubber bumper is manufactured in EPDM rubber to the original factory configuration. Was installed on...
1951-72 Buick, Chevrolet, Pontiac, Oldsmobile; Convertible Power Top Motor Mounting Grommet; Each
Reproduction of the original rubber mounting/insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a damper...
1958-75 Clutch Bellcrank Felt Seals ; Pair
OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...
Door, Vent, Quarter Glass; Sealstrip Glass Setting Tape;10 Foot Roll; 1/16" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
Sealstrip Glass Setting Tape ; 10 Foot Roll ; 3/64" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1956-60 Bel Air, 150, 210, Nomad, Impala, Bel Air, El Camino; Firewall Wire Harness Grommet; Each
Reproduction of the original firewall wire harness grommet for use with various 1956-60 Chevy Bel Air, 150, 210, Nomad, El Camino, Impala, Biscayne, and various other models including station wagons. This grommet is...
1968-76 Remote Outer Door Mirror Gasket ; Various Models
Reproduction of the original outer door remote mirror mounting gasket for use with the various applications listed. Each gasket is manufactured to replicate the original is fitment and design. Can be used with the original...
1955-79 Outer Door Handle Push Button O-Ring Gasket ; Each
This door handle O-ring is one of the most overlooked replacement parts on any vehicle. The O-ring inserts onto the outer door handle push button and eliminates rattling and wear between the handle and the push button....
Reproduction rubber bumper for various GM applications. Each bumper is manufactured in EPDM rubber to factory specifications replicating the original in design and fitment. This bumper was used for various applications...
1967-69 Camaro, Firebird; Plastic Clip Set; Radiator Support To Hood Seal; 9 Piece Set
Reproduction of the radiator support to hood seal clip set designed for 1967-69 Camaro and Firebird models with air conditioning. Each clip is injection molded to original specifications. Clips are designed to hold the hood...
Protect your engine bay from water, salt, and road debris with these OER reproduction splash aprons. Each superior reproduction set is manufactured to original specifications, ensuring the correct fit and appearance. Designed...
1968-72 Shift Plate Seal Set ; Chevelle, El Camino, Monte Carlo ; 4 Piece Set
Reproduction of the original shift plate seals designed for use on 1968-72 Chevelle models with automatic transmissions. These seals are manufactured from die cut high grade rubber and will fit as original. 4 piece set....
1966-1979 Camaro, Impala, Nova; Rubber Side Hood Bumper; Each
Reproduction of the original style side hood rubber bumper designed for use various GM models. Over time, the rubber stoppers on your hood can wear out or deteriorate. These reproduction stoppers will help keep your hood...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1954-1981 GM; Hood Adjustor Rubber Bumper & Stud; Various GM Cars & Trucks
Reproduction 5/16-18 x 1-1/2" hood bumper. Includes correctly threaded stud with a 1" diameter x 1/2" tall round rubber top. Helps keep the hood aligned when installed. Can be adjusted higher or lower. 2 hood adjust bumpers...
1970-90 GM; Lower Door Window Stop Bumper; Each; Various Models
Correct reproduction rubber stop bumper designed to keep the door glass from rolling down beyond the required travel point. Each stopper is manufactures from quality EPDM rubber and features a press fit retaining tab for easy...
1941-76 Mohair Window Channel Liner ; 2-5/8" wide x 8" long
When it comes to relining the door and quarter window channels, this Mohair liner material is what you'll need. A finely textured mohair lining material with a rubberized backing. Inside the door, there are "U" shaped...
1968-96 Impala, Chevelle, Corvette; Hood Rear Panel Bumper, Each, Various Models
Reproduction of the original rear hood panel bumper designed for use on various 1968-96 GM models. Exact reproduction of the original rear hood bumper used to replace the worn out or missing original. Manufactured to exact...
1964-65 Chevelle, El Camino; Front Fender Well Splash Apron Set; RH & LH; Pair
Replace the worn or missing splash aprons on your inner fender wells with this authentic OER reproduction set. Designed and manufactured to factory specifications, these premium splash aprons restore the correct seal between...
1955-76 Chevrolet Bel Air, 150, 210, Impala, Caprice; Fender Skirt Rubber Seal ; 120" Long; OER
Reproduction fender or quarter panel skirt rubber seal for various 1955-76 Chevrolet models. Manufactured to correct dimensions from quality EDPM rubber that replicates the original in fitment and appearance. Measures 120"...
1961-79 GM; Transmission Control Cable Grommet; OER
OER® reproduction of the original GM transmission control cable grommet for all 1961-79 GM models. Designed to factory specifications in the correct configuration for a perfect fit and manufactured in rubber as original....
1941-76 Mohair Window Channel Liner ; 1-5/8" Wide x 8" Long x 1/16" Thick
When it comes to relining the door and quarter window channels, this Mohair liner material is what you'll need. A finely textured mohair lining material with a rubberized backing. Inside the door, there are "U" shaped...