1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1957-69 Buick, 1968-70 Chevrolet; Vented Gas Cap; with Markings
Reproduction GM gas cap that includes the correct "S" rivet and properly engraved markings. Manufactured and designed from the original OEM cap, the quality and materials are manufactured to exact specification with the "show...
Reproduction fuel tank for 1964-67 Chevrolet Chevelle and Malibu sedan, hardtop and convertible models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion...
The most accurate reproduction fuel tank sending unit in the industry, with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and float as original. This unit...
Reproduction fuel tank for carbureted gasoline powered or diesel powered 1977-1990 Impala, Caprice, Buick, Oldsmobile, and Pontiac station wagon, El Camino and Caballero models. This fuel tank is manufactured in zinc-coated...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction fuel tank sending unit for 1965-66 Chevrolet Impala, Bel Air, Biscayne, Caprice models and 1965-67 Chevelle, El Camino, Malibu and other GM A-Body and B-Body models with 5/16" line. The most accurate reproduction...
Reproduction fuel tank sending unit for 1978-87 Chevrolet El Camino and GMC Caballero models equipped with a 17.5-gallon fuel tank. Manufactured to factory specifications, this sending unit accurately measures the fuel level...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1968-69 Chevelle, El Camino, GTO, Skylark, LeMans, Tempest; Accelerator Pedal Assembly
Reproduction accelerator pedal assembly for 1968-69 Chevelle, El Camino, GTO, Skylark, LeMans, and Tempest models. Manufactured to factory specifications, this assembly includes the pedal pad, mounting arm, and firewall...
1964 Impala, Bel Air, Biscayne; Fuel Tank Filler Grommet; Each
Reproduction of the original fuel tank filler grommet designed for use with 1964 Impala, Bel Air, Biscayne, 1964-67 El Camino, Chevelle, and Malibu station wagon models. Grommets are manufactured to correct dimensions...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
Reproduction fuel tank sending unit for 1968-70 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and 1970 Chevrolet Monte Carlo models. Manufactured to factory...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Reproduction fuel tank sending unit for 1964 Chevrolet Chevelle, El Camino, Pontiac GTO, LeMans, Tempest, Buick Skylark, and Oldsmobile Cutlass and 442 models. Manufactured to factory specifications, this sending unit...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reduce heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket and shield was original equipment for most 1970 Chevrolet...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1974-81 Outer Accelerator Pull Spring
Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction fuel tank for 1968-70 Chevrolet El Camino models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion prevention. This is a 20 gallon fuel tank...
1965-74 Holley; Carburetor Heat Shield; 4 Barrel with 396,454 Engine
OER® reproduction carburetor heat shield for all GM models with a Holley 4 bbl carburetor. This heat shield will help cool the intake charge for better performance. Original for 1970 396ci & 454ci with Special...
Reproduction of the original style fuel tank designed for use with 1977-1990 Impala, Caprice, Buick, Oldsmobile, and Pontiac station wagon models. This fuel tank is manufactured in zinc-coated stamped steel to original...
1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb
Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1967 Chevy, Pontiac; Accelerator Pad; with Steel Backing Plate; OE Style; Various Models
Reproduction of the original accelerator pedal pad designed for use on various 1967 GM models. This accelerator pedal pad is manufactured in the correct design based on a steel backing unlike the GM plastic replacements. The...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1970-72 Chevelle, El Camino, Monte Carlo, GTO, LeMans; 1970 Tempest; Accelerator Pedal Assembly
Reproduction accelerator pedal assembly for 1970-72 Chevelle, El Camino, Monte Carlo, GTO, and LeMans models, as well as 1970 Tempest. Manufactured to factory specifications, this assembly includes the pedal pad, mounting...
1965-70 Chevy, Dodge, Plymouth; Gas Cap; Non Vented; Non-Locking
Correct reproduction non-locking gas cap for various 1965-70 Chevrolet, 1968-70 Dodge & Plymouth models. This is a non-locking and non-vented cap that is for both 6 cylinder and V8 models. Chevrolet Applications: 1965-1970...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1958-60 Chevrolet; 6 Passenger Wagon, El Camino; Sedan Delivery; Fuel Sending Unit; with 3/8" Line
Reproduction fuel tank sender unit for 1958-60 Chevrolet 6-passenger station wagons, or 1959-60 El Camino models. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge...
1958-60 Chevrolet Station Wagon / El Camino; Fuel Sending Unit; With 5/16" Line
Reproduction fuel sender for 1958-60 Chevrolet full-size wagon or 1959-60 El Camino. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge with the signal to indicate fuel...
Reproduction fuel tank sending unit for 1964 Chevrolet Chevelle, El Camino, Pontiac GTO, LeMans, Tempest, Buick Skylark, and Oldsmobile Cutlass and 442 models. Manufactured to factory specifications, this unit accurately...
Reproduction fuel tank sending unit for 1964 Chevrolet Chevelle, El Camino, Pontiac GTO, LeMans, Tempest, Buick Skylark, and Oldsmobile Cutlass and 442 models. Manufactured to factory specifications, this unit accurately...
Reproduction fuel tank sending unit for 1971-72 Chevrolet Chevelle, El Camino, Monte Carlo, Pontiac GTO, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and GMC Sprint models. Manufactured to factory specifications, this...
Reproduction fuel tank sending unit for 1964 Chevrolet Chevelle, El Camino, Pontiac GTO, LeMans, Tempest, Buick Skylark, and Oldsmobile Cutlass and 442 models. Manufactured to factory specifications, this sending unit...
Reproduction fuel tank sending unit for 1968-70 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and 1970 Chevrolet Monte Carlo models. Manufactured to factory...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Reproduction fuel tank sending unit for 1971-72 Chevrolet Chevelle, El Camino, Monte Carlo, Pontiac GTO, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, and GMC Sprint models. Manufactured to factory specifications, this...
1955-86 Chevy, GMC, Pontiac; Fuel Pump Push Rod; Small Block / Big Block
Reproduction fuel pump push rod for 1955-86 Chevrolet, GMC, and Pontiac models. Fits Chevrolet small block, big block, and Pontiac V8 engines. 5-3./4" long x 1/2" dia.
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1978-88 Buick, Chevrolet Pontiac, Olds; Accelerator Pedal Pad; Various Models
Reproduction of the original accelerator pedal designed for use on various 1978-87 GM G-Body models. Manufactured in injection molded ABS to factory specifications replicating the original in quality and appearance. Will fit...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1968-72 Chevelle, GTO, Cutlass, GS; Fuel Tank Mounting Straps; Pair; Except Station Wagon Models
Reproduction of the original style fuel tank mounting straps for various 1968-72 GM A-body models including Chevelle, El Camino, GTO, LeMans, Gran Sport and Cutlass models. Each strap is manufactured in quality stamped steel...
Stainless steel fuel tank mounting straps for various 1968-72 GM A-body models including Chevelle, El Camino, GTO, LeMans, Gran Sport and Cutlass models. Each strap is manufactured in quality stainless steel with all correct...
Reproduction of the original style fuel tank mounting straps for 1964-67 Chevrolet Chevelle and Malibu Station Wagon models and El Camino. Each strap is manufactured in quality stamped stainless steel for long lasting...
Reproduction of the original style fuel tank mounting straps for 1964-67 Chevrolet Chevelle and Malibu Station Wagon models and El Camino. Each strap is manufactured in quality stamped steel and galvanized for long lasting...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...