Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1962-84 Windshield Washer Jar Cap ; Various GM Models
Reproduction of the original windshield washer jar cap designed for use on a variety of GM models including 1967-74 Camaro models. This cap is manufactured in injection molded ABS and replicates the original. Features correct...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models
Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1963-67 Chevrolet Corvette; Rear Bumper; Chrome; Driver Side; LH
Reproduction rear chrome bumper for 1963-67 Chevrolet Corvette models. Manufactured to factory specifications featuring correct mounting points and triple chrome plating. LH driver side. {fitment}
1963-67 Chevrolet Corvette; Rear Bumper; Chrome; Passenger Side; RH
Reproduction rear chrome bumper for 1963-67 Chevrolet Corvette models. Manufactured to factory specifications featuring correct mounting points and triple chrome plating. RH passenger side. {fitment}
1963-67 Chevrolet Corvette; Chrome Front Bumper; LH Driver Side
Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...
1963-67 Chevrolet Corvette; Chrome Front Bumper; RH Passenger Side
Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1956-62 Corvette; Convertible Top Motor Pump Assembly; Original Style; Made in the USA!
Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
1963-67 Chevrolet, Oldsmobile, Pontiac; Hood Hinge Assembly; RH Passenger Side
Reproduction hood hinge assembly for various 1963-67 GM models. Each hood hinge is manufactured from stamped steel to factory specifications assuring a quality replacement. Features correct mounting points for ease of...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Windshield Wiper Blades; Aero Style; 15"; for 1/4" (7mm) Bayonet Style Arms; Pair; Various Models
High quality reproduction of the stainless steel "Aero" Anti Wind-Lift Wiper Blades designed to fit 7mm wide bayonet style wiper arms. Popularized in the 1960's and 70's to combat wind lift at high speeds, these 15 inch wiper...
Reproduction front windshield glass for 1963-67 Chevrolet Corvette coupe & convertible models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road debris....