1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1957-69 Buick, 1968-70 Chevrolet; Vented Gas Cap; with Markings
Reproduction GM gas cap that includes the correct "S" rivet and properly engraved markings. Manufactured and designed from the original OEM cap, the quality and materials are manufactured to exact specification with the "show...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1999-07 Chevy, GMC GMT800 Pickup; Fuel Filler Door & Hinge Assembly
Reproduction fuel filler door for 1999-2007 Chevrolet, GMC GMT800 Series pickup trucks. This fuel door is manufactured to correct factory specifications and includes the fuel door, spring, and bracket for a complete...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reproduction of the original fuel tank mounting straps designed for use with 1999-2006 Chevrolet, GMC C/K pickup truck, Silverado, and Sierra models with saddle mounted 26 gallon gas tank. Each strap is manufactured in...
Reproduction of the original OE rubber bumper for use with 1979-86 Chevrolet and GMC C/K pickup truck models, and 1987-91 Chevrolet and GMC R/V models. Also fits other areas of the vehicle including the heat exhaust shield,...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1967 Chevy, Pontiac; Accelerator Pad; with Steel Backing Plate; OE Style; Various Models
Reproduction of the original accelerator pedal pad designed for use on various 1967 GM models. This accelerator pedal pad is manufactured in the correct design based on a steel backing unlike the GM plastic replacements. The...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevy Bel Air, 150, 210, Nomad, and 1931-62 Chevy and GMC pickup truck models. Correct replacement of the original fuel tank sending unit...
1967-72 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6. {fitment}