1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1968-69 Camaro V8 Throttle Arm
Reproduction of the original throttle arm designed for use on 1968-69 Camaro models. Each throttle arm is produced to replicate the original in quality and fit. Replace your worn out or damaged original throttle arm with this...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
1968-69 Camaro, 1968-74 Nova, Omega, Ventura; Accelerator Pedal Assembly; with V8
Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...
1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb
Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1967-69 Camaro, 1968-70 Nova Accelerator Pedal Rod ; V8
Reproduction of the original accelerator pedal pad rod designed for use on Camaro and Nova models. This rod connects between the throttle arm and the accelerator pedal. Manufactured in correct configuration, replaces the bent...
1967-02 Accelerator Pedal Mounting Pin
This special mounting pin is just what you need to correct a loose accelerator pad. This special design allows the pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems commonly...
1968-74 Accelerator Pedal Pad To Rod Support
Reproduction of the original accelerator pedal rod support for use on the various applications listed. Each support is manufactured in injection molded ABS offering an exact replacement of the original. Applications:...
1958-71 GM; Accelerator Pedal Ball Stud Pivot; 1/4"-20 x 1-1/2"; Various Models
Original factory ball stud pivot designed for use on various GM models. 1/4"-20 x 1-1/2". Accelerator pedal ball studs can break after many years of use and will need to be replaced. Check your stud for wear when replacing...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...
1968-69 396 Carb to Accelerator Lever Rod ; Big Block with 4 bbl Carb
Reproduction of the original 1968-69 accelerator pedal rod designed for use with 396 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is...
1968-72 Camaro, Impala, Nova; Quadrajet Throttle Cable Bracket
Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1967-77 GM Pedal Pad Kit - Auto Trans - 6 Piece Kit
This complete kit is designed to replace pedal pads and trim plates on a variety of Chevrolet models including 1967-68 Camaro with drum brakes and an automatic transmission as well as a variety of additional GM models as...
Powerglide Upper Kickdown Clip
OER® Authorized reproduction upper kickdown clip for models with powerglide automatic transmission. Connects the upper passing gear kickdown rod to the bellcrank assembly. Applications: 1967-69 Camaro with Powerglide...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...