1956 and 1958 Chevrolet Passenger Car; Rear Bumper to Body Seal
Reproduction of the original rear bumper to body seal designed for 1956 and 1958 Chevrolet full size passenger car models. Each body seal is manufactured to factory specifications from molded EPDM rubber. {fitment}
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1955-90 GM; Door Lock Gasket; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1966-72 Chevrolet; Standard Door Mirror Gasket
Quality reproduction outer door mirror gasket for various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors. Installs between the mirror base and...
1963-65 Chevrolet; Door Mirror Gasket ; LH or RH ; Various Models
Quality reproduction of the original outer door mirror gasket designed for use on various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors....
Reproduction of the original hood to cowl seal weatherstrip designed for use on 1991-96 Buick, Cadillac, Chevrolet, and Oldsmobile Full Size passenger car models. Each hood seal is manufactured from durable EPDM rubber in the...
1957-58 Chevrolet Full Size Passenger Car; Radiator Core Support Wiring Grommet
Reproduction radiator core grommet for 1957-58 Chevrolet passenger car models. This grommet is used to guide the wiring harness through the radiator core support and installs in the driver side of the core support panel....
1970-88 Buick, Chevrolet, Oldsmobile, Pontiac; Outer Door Handle Gasket; LH or RH ; Each
Reproduction door handle gasket for 1970-81 GM F-Body and 1973-88 G-Body models. This gasket inserts on the back of the outer door handle and acts as protection between the handle and the paint. Sold individually. 2 gaskets...
1962-81 Trunk Lock Cylinder Gasket ; Die-Cut Replacement
Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...
1958-75 Clutch Bellcrank Felt Seals ; Pair
OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...
1965-72 Chevrolet, Oldsmobile; Trunk Lock Cylinder Gasket; Molded Rubber
Reproduction of the original trunk lock cylinder gasket designed for use on various GM models. This gasket is used to seal the trunk lock cylinder to the body. Manufactured in quality EPDM molded rubber that replicates the...
1955-79 Outer Door Handle Push Button O-Ring Gasket ; Each
This door handle O-ring is one of the most overlooked replacement parts on any vehicle. The O-ring inserts onto the outer door handle push button and eliminates rattling and wear between the handle and the push button....
1962-78 Nova, Camaro, Firebird, Impala, Truck; Speedometer Cable Firewall Grommet; w/Steel Insert
Quality reproduction of the original speedometer cable firewall grommet designed for use on various 1962-73 Chevy II Nova, Camaro, Impala, Bel Air, Biscayne, Caprice, Firebird, and 1973-78 Chevrolet, GMC truck models as...
1965-67 Impala, Bel Air, Biscayne, Caprice; Hood To Cowl Seal Weatherstrip
High quality reproduction of the original weatherstrip seal that attaches to the front cowl panel and seals the area between the hood and windshield. This reproduction is manufactured to exact configuration allowing the seal...
1963-64 Impala, Bel Air, Biscayne; Hood to Cowl Seal Weatherstrip Seal
Quality reproduction of the original hood to cowl weatherstrip seal that attaches to the cowl panel and seals the area between the hood and windshield. This correctly configured seal is manufactured to exact specifications...
1964 Impala, Bel Air, Biscayne; Rear Bumper to Body Seal
Excellent reproduction of the original body seal strip designed to seal and fill the area where the rear bumper meets the body. This reproduction will install and fit as original offering an authentic appearance. This seal is...
1991-96 Impala, Caprice, GM Full Size; Rear Hood Cowl Outer Seals, Pair
Reproduction of the original rear hood outer corner rubber seals designed for use on 1991-96 Chevrolet Impala, Caprice and GM full size models. Each side seal is manufactured from durable EPDM rubber matching the original...
1982-98 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac; Door Jamb Switch Seal
Reproduction door jamb switch seal for the door jamb switch on a wide variety of GM models. Manufactured in rubber like the original, this accordian style seal prevent the elements from entering into the door jamb switch...