1961-68 GM Car; Various Models; Fuel Tank to Filler Neck Hose; 1-7/8 ID x 3 Long
Reproduction fuel tank to filler hose that seals the inlet filler neck to the tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1964-67 GM; Fuel Tank Sending Unit; 3/8"
The most accurate reproduction fuel tank sending unit in the industry, with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original....
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Mounting Brace; Each
Reproduction gas tank mounting brace for 1961-64 Impala, Bel Air, and Biscayne models. This brace attaches to the bottom of the trunk floor to support the gas tank. The gas tank mounting strap attaches to this brace....
Reproduction fuel tank for carbureted gasoline or diesel powered 1977-1990 Impala, Caprice, Buick, Oldsmobile, and Pontiac models. This fuel tank is manufactured in zinc-coated stamped steel to original factory...
1957-69 Buick, 1968-70 Chevrolet; Vented Gas Cap; with Markings
Reproduction GM gas cap that includes the correct "S" rivet and properly engraved markings. Manufactured and designed from the original OEM cap, the quality and materials are manufactured to exact specification with the "show...
1967-70 Impala, Bel Air, Biscayne, Caprice; Fuel Sending Unit; 3/8"; 0-90 ohm
Reproduction fuel sender for 1967-70 Impala, Bel Air, Biscayne, and Caprice models except station wagon models. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge with...
Reproduction fuel tank sending unit with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original. This unit monitors the fuel level in...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction fuel tank sending unit for 1961-64 Chevrolet Impala. Bel Air, and Biscayne models except station wagon. Each fuel sending unit is manufactured in quality steel to resist corrosion within your fuel tank. Provides...
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; 5/16"; Except Station Wagon
Reproduction fuel tank sending unit produced with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original. This unit monitors the fuel...
1955 Chevrolet Bel Air, 150, 210; Gas Filler Door Assembly; With Hinge and Spring
Reproduction fuel filler door assembly for 1955 Chevrolet Bel Air, 150, and 210 models. Each fuel door assembly is manufactured to correct factory dimensions offering an authentic replacement of the old, damaged, or worn out...
Reproduction fuel tank sending unit for 1965-66 Chevrolet Impala, Bel Air, Biscayne, Caprice models and 1965-67 Chevelle, El Camino, Malibu and other GM A-Body and B-Body models with 5/16" line. The most accurate reproduction...
1964 Impala, Bel Air, Biscayne; Fuel Tank Filler Neck; Gray Primer; Except Station Wagon Models
Reproduction of the original fuel tank filler neck designed for use with 1964 Impala, Bel Air, and Biscayne models (except station wagons). Each neck is manufactured to factory dimensions and replaces the original exactly....
A reproduction of the original upper fuel tank filler neck designed for use with 1957 Chevrolet Bel Air, 150, 210, and Del Ray, 2 & 4 door convertible, hardtop, and sedan models. Each filler neck is manufactured in quality...
1955-57 Chevy Bel Air, Corvette, 150, 210, Nomad; Accelerator Pedal Pad
Correct reproduction accelerator pedal for 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. Each pad is manufactured to correct factory specifications replicating the original in design and fitment. Features correct...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...