Headlamp Adjusting Screw ; For GM Models ; 1/4"-28 x 2"
Reproduction of the headlamp adjustment screw required for a wide variety of GM models including 1965-75 Impala, Biscayne, Bel Air and Caprice models. This 1/4"-28 adjustment screw comes zinc plated for corrosion resistance...
1962-71 GM Headlight 1/4"-28 x 1" Adjustment Screw with Nylon Nut
Original self-retaining nylon nut and 1/4"-28 x 1" screw assembly used for headlamp beam adjustment on 1962-71 GM models. This nut and screw mounts directly to the headlamp housing to enable the headlamp beam to be aimed...
OER® reproduction of the original headlamp adjusting spring designed for use on various GM models. This headlamp spring is used to adjust the headlight beam to the proper alignment. Applications: 1973-1974 Buick Apollo...
GM Headlamp Adjuster Screw And Nut Set - 8 Pieces
Replace damaged or missing headlamp adjusters with these quality reproductions. Each set includes 8 Pieces - (1) adjusting screw, (1) plastic adjusting nut, (2) mounting screws with (2) washers and (2) nuts. 4 sets are...
1967-68 Camaro, 1968 Chevelle, El Camino; Headlight Bezel Nut Set ; Set of 10
Reproduction of the original style barrel nuts designed for use on 1967-68 Camaro models. These unique barrel shaped plastic insert nuts press into the steel frame and provide a secure anchor for the trim screws. These...
1968 Camaro; Headlight Cover; RS; with Chrome Trim; LH
Correct reproduction of the original headlamp return cover (outer door) installed on all 1968 Camaro Rally Sport models. Manufactured in quality injection molded ABS replicating the original in quality and design. This return...
1967 Camaro RS; Headlight Bushing Set; 14 Piece Set
If you are rebuilding a 1967 Rally Sport headlamp assembly, then you'll want to replace the upper and lower headlight bushings. These bushings will help promote a smooth and efficient operation when the headlamps are...
1955-63 Chevrolet Full Size Headlamp Retaining Ring Spring; Second Design
Reproduction of the original spring used on the headlamp retaining ring spring for various 1955-63 Chevrolet models including Tri-5, Impala and Corvette models. Replaces OE #'s 5946543, 5948814 second design. {fitment}
1967-68 Camaro; Headlamp Cover; Rally Sport; RH; Black
Correct reproduction of the original headlamp return cover designed for use on 1967 Camaro Rally Sport (with hidden headlamps) models. Manufactured in injection molded ABS to factory specifications. This headlamp cover will...
1964-81 GM, Mopar; Headlight Bucket Tension Spring; Various Models; Each
Plated tension spring for headlight bucket to fit a wide variety of vehicle applications including GM and Mopar models. Closed back design is produced to allow the spring to be installed with a single phillips head screw...
1955-57 Chevrolet 150, 210, Bel Air; Headlamp Adjuster Set; Headlamp Bucket Rebuild Kit
Replacement headlamp adjuster set to repair the headlight buckets on 1955-57 Chevrolet passenger car models. Each set includes 39 total pieces - (2) headlight adjusting screws, (2) plastic replacement adjusting screw nuts,...
1968 Camaro; RS Headlamp Bell Crank Spring and Bracket Set ; 8 Piece Set
Keys onto lower end of headlamp bell crank and acts as an over center counter balance assist. This set includes two attachment brackets which install on the lower edge of the headlamp housing and allow correct closure of the...
1967-69 Camaro RS Headlamp Pivot Bolt ; Each
Reproduction of the original bolt used to pivot the Rally Sport headlamp doors on 1967-69 Camaro models. This bolt installs through the control opening hinge and attaches the hinge to the headlamp housing on RS (hidden...
1968 Camaro RS; Headlight Bellcrank ; LH Drivers Side
Reproduction of the original 1968 Camaro Rally Sport bellcrank. The bellcrank installs from the headlamp actuator to the main headlamp housing assembly and enables the headlamp door to open and close when activated. Includes...
1957 Chevy Bel Air, 150, 210, Nomad; Headlamp Bezel Screw Set
Reproduction headlamp bezel screws for all 1957 models. Manufactured in the correct size and finish. One set required per vehicle.
1962-68 Impala and Fullsize; 1/4-28 x 1" GM Headlamp Adjuster Screw With Nylon Nut; 16 Piece Set
Correct reproduction of the headlamp beam adjusting hardware set for various 1962-up GM models. Includes (8) nylon nuts, (8) 1/4"-28 x 1" adjuster screws. Each 16-piece set includes enough adjusters for both the right and...
1/4"-28 GM Headlight Beam Nylon Adjuster Nut
This 1/4"-28 headlight beam adjusting nut mounts directly to the headlamp housing and enables the headlamp beam to be aimed correctly. Fits a wide variety of GM vehicles from 1962-on. Use as required. Sold individually....
Screw #8 X 1" with #6 Phillips Head Tapping Screws; Chrome; Set of 4
Set of 4 screws used to attach various parts including 1974-78 Mustang II headlamp bezels # 13064P.
1947-57 GM Headlamp Adjusting Screw and Nut Set
Headlamp Adjustment screw set for various 1947-57 GM models including Bel Air, Nomad, and Pickup. The correct hardware will make your installation easier, and give your classic a finished look. Sets includes adjuster screws...
1999-2002 Chevrolet Truck; Headlamp Housing Support; Drivers Side
Reproduction of the original headlight housing support designed for use with 1999-02 Chevrolet Silverado models. The housing support is manufactured in ABS plastic to original factory dimensions. Will replace the original...