Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; RH Passenger Side; Various Models
This OER® reproduction door hinge restores proper door operation on 1970-81 models. The factory doors were extremely heavy and often caused the original hinges to wear or sag over time. Replacing them with this...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
OER reproduction windshield glass for various Buick, Chevrolet, Pontiac, and Oldsmobile B & C-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against...
OER reproduction windshield glass for various GM B & C-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road debris. Windshield is supplied in a...
Reproduction of the original front windshield glass for use with 1965-68 Buick, Chevrolet, Pontiac, and Oldsmobile Full Size 2 & 4 door sedan, and station wagon models as listed. Windshield comes in a light green tint with...
1969-70 Full-Size Chevrolet 4 Door Sedan & Station Wagon Tinted Windshield Glass With Antenna
Replacing your original damaged or missing windshield glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the...
1964-72 Buick, Cadillac, Chevy, Pontiac, Oldsmobile; Convertible Top Latch Knuckle Hook; Each
Reproduction of the original latch knuckle hook designed for use with various GM convertible models. This component secures the convertible top to the upper windshield header, ensuring a proper seal and stable fit. Each...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
Reproduction power window lift motor for various 1979-2005 GM models. Return your power windows to good working order by replacing your missing or nonfunctional original motor with this brand new reproduction motor. Buick...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction of the original front 3-hole door window glass. Each glass is manufactured with the proper shape, curvature, and pattern in OEM equivalent material. Replace scratched, damaged or missing original glass with this...
Reproduction of the original 3-hole rear door window glass. Each glass is manufactured with the proper shape, curvature, and pattern in OEM equivalent material. Replace scratched, damaged or missing original glass with this...
OER reproduction front door glass for 1977-79 GM Full Size models as listed. Each glass is manufactured with the proper shape, curvature, and pattern in OEM equivalent material. Replace scratched, damaged or missing original...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile convertible models. Manufactured in quality zinc die-cast metal, each...
OER reproduction front door glass for 1977-79 GM Full Size models as listed. Each glass is manufactured with the proper shape, curvature, and pattern in OEM equivalent material. Replace scratched, damaged or missing original...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 GM convertible models. Manufactured in quality zinc die-cast metal, each knuckle is built to OE factory specifications for...
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
1982-13 Buick, Chevy, Olds, Pontiac; Lower Door Hinge Spring; Each; Various Models
Reproduction of the original door hinge spring designed for use on various 1982-13 GM models including the popular 1982-92 Camaro and Firebird models. After just a few short years, the original door hinge springs will usually...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
Correct reproduction washer pump for various 1973-1984 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models. Each pump is engineered to match original equipment washer pump in functionality, fitment, and cosmetic...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Correct reproduction of the original storage sleeve for the trunk wheel jack and wrench unit. This special storage sleeve was found originally on many GM car models. Manufactured from quality rubber material, this sleeve...
1961-87 Buick, Chevrolet, Pontiac, Olds; Door Lock Set; with Generic Logo Keys; Bright Finish
Reproduction door lock cylinders for various 1961-87 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed. Includes two door lock cylinders with bright finish face finish, two generic logo keys, cylinder...
Reproduction convertible front tack strip for various 1959-76 GM convertible models. This is an essential item for anyone installing a new top on their convertible. This durable tack strip will effectively secure the new top...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
Reproduction windshield wiper arm for various 1977-90 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac B, C, and D-Body models. Each wiper arm is manufactured to correct factory specifications, replicating the original...
Replacement washer pump for various 1970-2019 General Motors vehicles. This quality replacement washer pump is an alternative to the original, and more expensive Delco washer pump. Installs as original and offers years of...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
1973-84 GM; Windshield Washer Pump Plastic Cover; Second Design
Correct reproduction windshield washer pump plastic cover for 1973-84 GM models. This is a new 2nd design wiper pump cover for many classic GM vehicles with recessed wipers and wiper motor with external terminal board. This...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
Bolt, 1/4-20 x 1-3/16" Dog Point Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 x 1" Pointed Tip With Hex Washer Head, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 X 7/8" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...