Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
OER reproduction of the original front windshield glass for use with various Buick, Cadillac, Oldsmobile E-Body 2 & 4 door coupe, and convertible models as listed below. This windshield is manufactured with tempered laminate...
1966-1970 Riviera, Eldorado, Toronado; Windshield Glass; Tinted with Shade & Built-In Antenna
OER reproduction windshield glass for various 1966-70 GM E-Body 2-door hardtop models. Replacing your original damaged or missing windshield glass will enhance your vehicle's appearance and safety by allowing you to see...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
1970 Buick Skylark, LeSabre, Riviera; Mirror; Outside Remote; Chrome; LH
Replacement chrome remote outside mirror assembly for 1970 Buick Skylark, Riviera and LeSabre models. This a complete assembly that include the bracket, gasket, and the mirror with the cable and chrome knob. LH Driver side.
OER reproduction front windshield glass for use with various 1971-76 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile B-Body 2 & 4 door, coupe and hardtop models. This windshield is manufactured with tempered laminate...
1970-72 Buick; External Mirror; Manual Adjusment; RH Side With Buick Tri-Shield Logo
Reproduction of the original exterior rear view mirror that mounts to the RH, passenger side door, on all 1970 Buick models, and 1971-72 Buick Skylark, GS, and Sportwagon models. Each die-cast mirror is an exact replica of...
OER reproduction windshield glass for various Buick, Chevrolet, Pontiac, and Oldsmobile B & C-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against...
OER reproduction windshield glass for various GM B & C-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road debris. Windshield is supplied in a...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
Reproduction OEM accessory rubber trunk mat with Buick shields logo for 1961-77 Buick models including Skylark, Electra and Riviera. This is an auxiliary mat that goes on top of the felt covering. This is an officially...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1961-65 GM Full Size; Vent Window Regulator; Passenger Side; GM B Body Models
Reproduction of the original vent window requlator designed for use on various 1961-65 GM Buick, Chevrolet, Oldsmobile, and Pontiac full size models. Each regulator is designed and manufactured to replicate the original in...
Reproduction rear trunk lid hinges for 1961-64 Chevrolet, 1963-64 Oldsmobile, and 1963-65 Buick full size hardtop and sedan models (will not fit convertible models). The trunk lid hinges are manufactured to factory dimensions...
1979-1985 Riviera, Eldorado, Seville, Toronado; Hood Release Cable & Mounting Bracket
Reproduction hood release cable with the mounting bracket and grommet for 1979-85 Toronado, Seville, Eldorado and Riviera models. This replaces the original exactly. Sold individually. GM# 20429338.
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
Reproduction power window lift motor for various 1979-2005 GM models. Return your power windows to good working order by replacing your missing or nonfunctional original motor with this brand new reproduction motor. Buick...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
1976-88 Buick, Chevy, Pontiac Olds; Exterior Door Handle; Black; LH Driver Side; Various Models
Reproduction of the original style exterior door handle designed for use with various 1976-88 Buick, Chevrolet, Pontiac, and Oldsmobile models. This door handle is produced in die-cast metal featuring a glossy black finish...
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1982-13 Buick, Chevy, Olds, Pontiac; Lower Door Hinge Spring; Each; Various Models
Reproduction of the original door hinge spring designed for use on various 1982-13 GM models including the popular 1982-92 Camaro and Firebird models. After just a few short years, the original door hinge springs will usually...
1977-2005 Buick, Chevy, Pontiac, Oldsmobile;;Hood Latch Assembly; Various Models
Reproduction hood latch assembly for various 1977-2005 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed below. Each latch is designed as a direct replacement for the worn or inoperative original....
Correct reproduction washer pump for various 1973-1984 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models. Each pump is engineered to match original equipment washer pump in functionality, fitment, and cosmetic...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
1971?73 Buick & Oldsmobile License Plate Bracket; except Station Wagon Models
Upgrade your restoration or replace a damaged original with this high-quality reproduction license plate bracket, designed specifically for 1971?1973 Buick and Oldsmobile models, excluding station wagons. Manufactured to...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Correct reproduction of the original storage sleeve for the trunk wheel jack and wrench unit. This special storage sleeve was found originally on many GM car models. Manufactured from quality rubber material, this sleeve...
1961-87 Buick, Chevrolet, Pontiac, Olds; Door Lock Set; with Generic Logo Keys; Bright Finish
Reproduction door lock cylinders for various 1961-87 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed. Includes two door lock cylinders with bright finish face finish, two generic logo keys, cylinder...
1976-88 Buick, Chevy, Pontiac, Olds; Outer Door Handle; Chrome; Front or Rear; LH; Various Models
Reproduction of the original style front or rear outer door handle designed for use with various 1976-88 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each handle is manufactured to correct factory...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
Replacement washer pump for various 1970-2019 General Motors vehicles. This quality replacement washer pump is an alternative to the original, and more expensive Delco washer pump. Installs as original and offers years of...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
Reproduction exterior mirror mounting gasket for various 1971-79 GM models with standard chrome mirrors. Each gasket is manufactured to factory specifications. Fits LH or RH side of the vehicle.
1973-84 GM; Windshield Washer Pump Plastic Cover; Second Design
Correct reproduction windshield washer pump plastic cover for 1973-84 GM models. This is a new 2nd design wiper pump cover for many classic GM vehicles with recessed wipers and wiper motor with external terminal board. This...
Reproduction push-in retainer for a wide variety of GM vehicle applications. Specifically fits the windshield washer bottle on 1982-1992 Camaro, Firebird, and various Chevrolet models (2 required per vehicle). Also commonly...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
1971-79 Pontiac, Buick, Oldsmobile, Cadillac; Hood Latch Pop-Up Spring; Various Models; GM# 408576
Replacement hood lock pop-up spring for multiple 1971-79 GM applications including LeMans, Toronado, Apollo models. This is the spring that mounts to the hood latch and pops the hood up to get to the safety catch to open the...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...