Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
1982-04 GM; Hood Adjustment Bumper and Bolt; 1" Diameter Rubber Stopper
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1969-76 Buick Skylark, Electra, LeSabre; Rear Cowl Hood Stop Stud/Bolt; Rubber Coated; GM# 1237800
Rear cowl hood stop bolts for various 1969-76 Buick models including Skylark, Riviera, LeSabre and Electra models.This is the rubber coated hood stop bolt. It mounts on the cowl panel by the windshield when you close the...
Reproduction of the rubber bumper to fit a variety of GM models and applications. Sold individually. Refer to detailed applications below. Buick Applications- For Door Pull Handles: Regal 1991-92 - rear door Skylark 1986-91 -...
1961-79 GM; Bucket Seat Back Rubber Stopper Set; Round; w/Mounting Screws; Pair
Reproduction of the original seat back rubber stoppers designed for use on various 1961-79 GM models. These rubber stoppers help prevent rattling and keep the seat back positioned correctly. Replace worn out or missing seat...
1980-2016 GM; Hood Adjust Rubber Bumper; Outer Side; Each
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1963-90 GM; Rubber Bumper; Various Applications
Reproduction rubber bumper for various GM applications. Each bumper is manufactured in EPDM rubber to factory specifications replicating the original in design and fitment. This bumper was used for various applications as...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1954-1981 Hood Adjustor Bumper and Stud - Various GM vehicles
Reproduction 5/16-18 x 1-1/2" hood bumper. Includes correctly threaded stud with a 1" diameter x 1/2" tall round rubber top. Helps keep the hood aligned when installed. Can be adjusted higher or lower. 2 hood adjust bumpers...
1977-2005 Buick, Chevy, Olds, Pontiac; Compartment Lid Rubber Bumper; Front or Rear
Reproduction of the original rear compartment lid rubber stopper needed to prevent the rear compartment lid from slamming against the body. Each rubber bumper is manufactured in quality EPDM rubber that replicates the...
1965-92 Outer Door Rubber Bumper; Various Models
Reproduction of the original rubber stopper designed for use on the upper door section of the various GM models listed below. Each rubber stopper is manufactured to replicate the original in fitment and appearance. This...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper;Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM rubber ensuring a quality reproduction...