1964-72 Buick, Chevrolet, Oldsmobile, Pontiac; Fuel Tank Vent Tube Grommet; Each
Replacement vent tube grommet for 1964-72 GM models. Manufactured to factory dimensions, this molded rubber grommet fits in the trunk pan and features two holes for the fuel vent tube to pass through. {fitment}
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1955-90 GM; Door Lock Gasket; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...
1964-79 GM; Door Handle Gasket Set; Outer; Various Models
This reproduction gasket set includes a complete set of door handle gaskets used to install the outer door handles on the various models listed below. Each set includes correct die-cut gaskets for both RH and LH outer door...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
Correct reproduction of the original U-shape rubber molded weatherstrip seal originally installed on 1969-70 Buick, Chevy, Pontiac, and Oldsmobile Full Size hardtop & convertible passenger car models. This seal attaches to...
Reproduction of the original hood to cowl seal weatherstrip designed for use on 1991-96 Buick, Cadillac, Chevrolet, and Oldsmobile Full Size passenger car models. Each hood seal is manufactured from durable EPDM rubber in the...
1970-88 Buick, Chevrolet, Oldsmobile, Pontiac; Outer Door Handle Gasket; LH or RH ; Each
Reproduction door handle gasket for 1970-81 GM F-Body and 1973-88 G-Body models. This gasket inserts on the back of the outer door handle and acts as protection between the handle and the paint. Sold individually. 2 gaskets...
1962-81 Trunk Lock Cylinder Gasket ; Die-Cut Replacement
Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...
1967-68 Impala, Wildcat, Delta 88; Roof Rail Weatherstrip Seal, 2-Door Fastback; Pair
Reproduction of the original roof rail weatherstrip designed for use on 1967-68 Impala 2 door Fastback, Wildcat, Le Sabre, and various GM models as listed below. This quality reproduction weatherstripping is manufactured in...
1970-81 Camaro, Firebird, Nova, Ventura; Upper Clutch Push Rod Boot; Various Models
OER® reproduction upper clutch push rod boot for various 1970-81 Buick, Chevrolet, Oldsmobile and Pontiac models. Each clutch rod boot is manufactured in quality EPDM rubber matching the original boot cosmetically in...
Reproduction door frame weatherstrip set for Chevrolet Impala and other GM Full Size 2-door hardtop and convertible models. This reproduction is designed to replace the original exactly featuring the correct molded ends and...
1955-79 Outer Door Handle Push Button O-Ring Gasket ; Each
This door handle O-ring is one of the most overlooked replacement parts on any vehicle. The O-ring inserts onto the outer door handle push button and eliminates rattling and wear between the handle and the push button....
1969-77 Camaro, 1973-74 X Body; Rear License Bracket Rubber Bumpers; 13/16" Tall; Pair
Reproduction license plate / fuel door stoppers for the rear license bracket. These are OE type reproductions manufactured to exact OE specifications. Sold in pairs. 9/16" diameter, 13/16" tall. GM Note: REV. 5-80 (cut 1/4"...
1967-74 Upper Clutch Push Rod Boot - Various Models
This OER® reproduction of the original upper push rod molded rubber boot is manufactured using correct E.D.P.M. rubber compound stock that is superior to the original. Molded in steel insert distributes mounting screw...
Correct reproduction of the original power window harness rubber boots which is used to house the power window wiring harness as it passes between the door jamb and door area. This rubber boot is manufactured in durable...
1955-58 Buick, Cadillac, Chevy, Pontiac, Olds; Windshield Pillar Post Weatherstrip; Pair
Reproduction of the original pillar post weatherstripping designed for use on various 1955-58 Buick, Cadillac, Chevy, Pontiac, and Oldsmobile models including 1955-57 Bel Air and full size Chevrolets. Replacing the windshield...
1991-96 Impala, Caprice, GM Full Size; Rear Hood Cowl Outer Seals, Pair
Reproduction of the original rear hood outer corner rubber seals designed for use on 1991-96 Chevrolet Impala, Caprice and GM full size models. Each side seal is manufactured from durable EPDM rubber matching the original...
1982-98 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac; Door Jamb Switch Seal
Reproduction door jamb switch seal for the door jamb switch on a wide variety of GM models. Manufactured in rubber like the original, this accordian style seal prevent the elements from entering into the door jamb switch...