Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1962-84 Windshield Washer Jar Cap ; Various GM Models
Reproduction of the original windshield washer jar cap designed for use on a variety of GM models including 1967-74 Camaro models. This cap is manufactured in injection molded ABS and replicates the original. Features correct...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-60 GM B-Body Convertible; Top Only; Canvas Cloth; Black
Reproduction convertible top, manufactured using heavy weight Stayfast Canvas Cloth materials and original manufacturing techniques to assure you receive the best quality replacement top on the market! Seams are highly...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
OER reproduction of the original front windshield glass for use with various Buick, Cadillac, Oldsmobile E-Body 2 & 4 door coupe, and convertible models as listed below. This windshield is manufactured with tempered laminate...
1976-81 Firebird; 1975-79 Nova, GM X-Body; Subframe Body Mount Bushing; # 3 Position; Upper Bushing
Reproduction of the original GM sub frame body mount for 1976-81 Firebird and 1975-79 Nova/GM X-Body models. Each body mount is produced using correct compression molded S.B.R. with steel sleeve that replicates the original...
1961-64 GM B-Body Convertible; Top Only; Use With Plastic Curtain; Canvas Cloth; Black
Reproduction convertible top, manufactured using heavy weight Stayfast Canvas Cloth materials and original manufacturing techniques to assure you receive the best quality replacement top on the market! Seams are highly...
1971-75 Impala/GM B-Body Convertible; Top Only; Stayfast Canvas Cloth; Black
Reproduction convertible top, manufactured using heavy weight Stayfast Canvas Cloth materials and original manufacturing techniques to assure you receive the best quality replacement top on the market! Seams are highly...
1961-62 Impala / Fullsize 4 Door Hardtop Smoke Back Glass
Replacing your original damaged or missing back glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the windows of...
1968-69 Camaro, Firebird, 1968-79 Nova, X-body; Door Hinge Rebuild Kit
Reproduction of the original components necessary to rebuild the door hinges on various GM models. Each door hinge set includes hinge pins, retaining clips, bushings, tension springs, roller detent studs and hardware for...
Replace the worn or rusted out rear convertible tack strip floating rear bow with this quality reproduction. Also referred to as the rear tacking rail or trimstick, this one piece tack strip bow mounts below the rear window...
1968-79 Camaro, Chevelle, Impala, Nova, Ventura; Rear License Plate Bracket; with Hinge; EDP Coated
Reproduction rear license plate bracket for various 1968-79 GM models including 1969-77 Camaro, 1968-71 Impala, 1968-72 Chevelle, 1968-79 Nova, Omega, Apollo, Ventura, and more. Manufactured in stamped steel to factory...
1969-81 GM; Door Hinge Repair Set ; Except with 15mm OD Bushings
Reproduction of the original door hinge components for use on various GM models. Repair the broken door hinges with this comprehensive repair set. Each repair kit includes 4 properly hardened shoulder pivot pins and 8...
1963-64 Impala 4 Door Hardtop Back Glass - Smoke
Replacing your original damaged or missing back glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the windows of...