1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1957-69 Buick, 1968-70 Chevrolet; Vented Gas Cap; with Markings
Reproduction GM gas cap that includes the correct "S" rivet and properly engraved markings. Manufactured and designed from the original OEM cap, the quality and materials are manufactured to exact specification with the "show...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1999-07 Chevy, GMC GMT800 Pickup; Fuel Filler Door & Hinge Assembly
Reproduction fuel filler door for 1999-2007 Chevrolet, GMC GMT800 Series pickup trucks. This fuel door is manufactured to correct factory specifications and includes the fuel door, spring, and bracket for a complete...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reduce heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket and shield was original equipment for most 1970 Chevrolet...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction of the original style fuel tank designed for use with 1970-74 Impala, Bel Air, Biscayne, Catalina, Bonneville and GM full size station wagon models. This fuel tank is made of zinc-coated steel and has a capacity...
Reproduction of the original style fuel tank designed for use with 1968-70 Impala, Bel Air, Biscayne, Catalina, Bonneville station wagon models. This fuel tank is made of zinc-coated steel and has a capacity of 22 gallons (91...
Reproduction clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86 Chevrolet/GMC Truck 1965-70...
2010-15 Chevrolet Camaro; Gas Door Cover; For Fuel Door; Paintable
Personalize your Gen 5 Camaro with a unique die-cast accessory fuel door cover. Each cover is manufactured to the same high standards of quality as regular production parts, guaranteeing a part that will stand up to years of...
1965-74 Holley; Carburetor Heat Shield; 4 Barrel with 396,454 Engine
OER® reproduction carburetor heat shield for all GM models with a Holley 4 bbl carburetor. This heat shield will help cool the intake charge for better performance. Original for 1970 396ci & 454ci with Special...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1958-60 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; with 348 ci; 3/8" Inlet
Reproduction fuel tank sending unit for 1958-60 Chevrolet Impala and Full Size models with 348ci engines. Features the original design for an authentic fit and genuine appearance. Each sending unit includes the sender,...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1958-60 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; 5/16" Inlet; 6 or 8 Cyl.; Except 348 ci
Reproduction fuel tank sending unit for various 1958-60 Chevrolet Impala and Full Size hardtop and sedan models. Features the original design for an authentic fit and genuine appearance. Each sending unit includes the sender,...
1961-64 Impala, Bel Air, Biscayne 6 Pass Station Wagon; Fuel Tank Sending Unit; with 5/16" Line
Reproduction of the original fuel tank sending unit designed for use with 1961-64 Chevrolet Impala, Bel Air, and Biscayne station wagon models with 5/16" line. Each sender is produced in quality steel to resist corrosion...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1958-60 Chevrolet; 6 Passenger Wagon, El Camino; Sedan Delivery; Fuel Sending Unit; with 3/8" Line
Reproduction fuel tank sender unit for 1958-60 Chevrolet 6-passenger station wagons, or 1959-60 El Camino models. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge...
1958-60 Chevrolet Station Wagon / El Camino; Fuel Sending Unit; With 5/16" Line
Reproduction fuel sender for 1958-60 Chevrolet full-size wagon or 1959-60 El Camino. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge with the signal to indicate fuel...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1964-71 Chevrolet, GMC; Floor Mounted Accelerator Pedal Pad Trim Plate; Various Car & Truck Models
Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Each trim plate is manufactured in stamped stainless offering long lasting dependability and an authentic appearance. This...
1969-81 GM; Fuel and Brake Line Clip; Dual Line 3/8" & 1/4"; Each
This correct reproduction line clip is designed for securing fuel and brake lines to the frame on a variety of GM models. Manufactured from durable galvanized steel, this clip is engineered to accept one 3/8 inch and one 1/4...
1964-71 Chevrolet; Floor Mounted Accelerator Pedal Pad; Rubber; with Steel Insert; OEM Reproduction
Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...
1968-74 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Pad to Rod Support
Reproduction of the original style GM accelerator pedal rod support for use on the various Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each support is manufactured in injection molded ABS offering an exact...
1969-81 GM; Fuel & Brake Line Clip Set; Dual Line 3/8" and 1/4"; 7 Piece Set
This correct reproduction line clip is designed for securing fuel and brake lines to the frame on a variety of GM models. Manufactured from durable galvanized steel, this clip is engineered to accept one 3/8 inch and one 1/4...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...
Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevy Bel Air, 150, 210, Nomad, and 1931-62 Chevy and GMC pickup truck models. Correct replacement of the original fuel tank sending unit...
1967-78 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
1968-72 Camaro, Impala, Nova; Quadrajet Throttle Cable Bracket
Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...
Reproduction of the original style components necessary to Install the fuel tank sending unit for 1949-1966 Chevrolet, GMC pickup truck, Suburbans, and 1958-1960 Impala, Bel Air, Biscayne, and full size models as losted. This...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...
1961-81 GM; Fuel Tank Sending Unit Gasket; Small; 1-13/16 ID; Various Models
Correct replacement fuel tank sending unit gasket for various 1961-81 Buick, Chevrolet, Oldsmobile and Pontiac models. This gasket installs between the sending unit and the locking ring. Gasket is manufactured to correct...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6.
1967-2000 GM; Fuel Sender Unit Lock Ring and Rubber Gasket; 2 Piece Set; Except Station Wagon Models
Reproduction of the original style fuel sending unit lock ring and gasket for use with various 1967-2000 Buick, Chevrolet, Pontiac, and Oldsmobile models. Install the sending unit on your vehicle with a new sending unit lock...